Airtac MICJ Adjustable Mini Cylinder MICJ16X75-40S
The AirTAC MICJ Adjustable Mini Cylinder MICJ16X75-40S is a genuine double acting, double rod, adjustable stroke + cushion round-body mini air cylinder with a Ø16mm bore and 75mm stroke, M5×0.8 air ports and a stainless-steel barrel and rod for mildly corrosive environments. Its ISO 6432 mounting interface fits standard ISO 6432 mini-cylinder mounting interfaces.
- BoreØ16 mm
- Stroke75 mm
- Port sizeM5×0.8
- Acting typeDouble acting, double rod, adjustable stroke + cushion
- Rod threadM6×1.0
- CushionVariable air cushion, both ends
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MICJ Adjustable Mini Cylinder MICJ16X75-40S
Trim the forward stop by up to 40 mm on site with the AirTAC MICJ16X75-40S, a stainless round-body mini cylinder built for double-acting service. An external screw shortens the extend end position (usable range 35-75 mm) while a needle-set adjustable air cushion at both ends soaks up high-speed shock. The M5×0.8 port and M6x1.0 male rod thread drop into standard ISO 6432 mini-cylinder mounting interfaces.
The -S suffix means a built-in piston magnet is present, allowing CMSG, DMSG, or EMSG sensors to track position. The stainless barrel and rod resist mild corrosion and washdown environments.
Airtac MICJ Adjustable Mini Cylinder MICJ16X75-40S Technical Specifications
| Model | Airtac MICJ Adjustable Mini Cylinder MICJ16X75-40S |
|---|---|
| Series | MICJ ISO 6432 mini cylinder |
| Bore size | Ø16 mm |
| Stroke | 75 mm |
| Acting type | Double acting, double rod, adjustable stroke + cushion |
| Port size | M5×0.8 |
| Rod thread | M6×1.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Variable air cushion, both ends |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G.
Theoretical Output Force (Ø16mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 86 N |
| 0.7 MPa | 121 N |
| Max (@1.0 MPa) | 18 kgf |
MIJ / MICJ are double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
Model Code: Airtac MICJ Adjustable Mini Cylinder MICJ16X75-40S
| MICJ | ISO 6432 round-body mini cylinder (adjustable-stroke, variable cushion). |
|---|---|
| 16 | Bore size in mm. |
| ×75 | Stroke length in mm. |
| -40 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (double rod, adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MICJ Adjustable Mini Cylinder MICJ16X75-40S Is Used
Package Diverting
Divert lightweight cartons on a conveyor at speed, using the adjustable air cushion to decelerate the 5.1 kg load smoothly before the end of stroke.
Sensor Tracking
Use the built-in -S magnet with DMSG sensors to confirm retraction on a washdown stainless assembly line, dialing the extend stop back 20 mm for a shorter reach.
Is the Airtac MICJ Adjustable Mini Cylinder MICJ16X75-40S the Right Cylinder?
When sizing this 16 mm bore, step down to an MIJ bumper-only cylinder for lighter duties, or step up to a Ø20 MICJ if you need the 157.0 N @0.5 MPa push force. The adjustable stop plus cushion shines in fast set-position moves where you must dial in a precise forward endpoint without swapping cylinders. For mounting, use LB foot, FA flange, or TC trunnion brackets (the SDB pivot block is not offered on this adjustable variant). Remember the stop screw sets the end position but is not a mid-stroke lock; the cylinder drifts on air loss, so fit an external rod lock or pilot check valve to hold a suspended load.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MICJ Adjustable Mini Cylinder MICJ16X75-40S FAQ
An external screw shortens the extend stroke by up to 40 mm (retract remains full), and a needle valve adjusts the air cushion at both ends to absorb high-speed shock. The cushion only decelerates near stroke end and does not lock the piston; the cylinder drifts on air loss.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC MICJ Cylinders
Request a Quote for Airtac MICJ Adjustable Mini Cylinder MICJ16X75-40S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.