Airtac MICJ Adjustable Mini Cylinder MICJ16X75-75S
The AirTAC MICJ Adjustable Mini Cylinder MICJ16X75-75S is a genuine double acting, double rod, adjustable stroke + cushion round-body mini air cylinder with a Ø16mm bore and 75mm stroke, M5×0.8 air ports and a stainless-steel barrel and rod for mildly corrosive environments. Its ISO 6432 mounting interface fits standard ISO 6432 mini-cylinder mounting interfaces.
- BoreØ16 mm
- Stroke75 mm
- Port sizeM5×0.8
- Acting typeDouble acting, double rod, adjustable stroke + cushion
- Rod threadM6×1.0
- CushionVariable air cushion, both ends
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MICJ Adjustable Mini Cylinder MICJ16X75-75S
Trim the forward stop by up to 75 mm on site without swapping cylinders, and let the adjustable air cushion at both ends soak up high-speed shock. The AirTAC MICJ16X75-75S is a double-acting, round-body stainless-steel mini cylinder that lets you dial in the extend end position and control the impact. Its stainless barrel and Ø6 mm piston rod resist mild corrosion and washdown environments.
It uses an M5×0.8 port and an M6x1.0 male rod thread. Because this SKU includes the -S magnet, it supports CMSG, DMSG, and EMSG sensors for position detection.
Airtac MICJ Adjustable Mini Cylinder MICJ16X75-75S Technical Specifications
| Model | Airtac MICJ Adjustable Mini Cylinder MICJ16X75-75S |
|---|---|
| Series | MICJ ISO 6432 mini cylinder |
| Bore size | Ø16 mm |
| Stroke | 75 mm |
| Acting type | Double acting, double rod, adjustable stroke + cushion |
| Port size | M5×0.8 |
| Rod thread | M6×1.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Variable air cushion, both ends |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G.
Theoretical Output Force (Ø16mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 86 N |
| 0.7 MPa | 121 N |
| Max (@1.0 MPa) | 18 kgf |
MIJ / MICJ are double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
Model Code: Airtac MICJ Adjustable Mini Cylinder MICJ16X75-75S
| MICJ | ISO 6432 round-body mini cylinder (adjustable-stroke, variable cushion). |
|---|---|
| 16 | Bore size in mm. |
| ×75 | Stroke length in mm. |
| -75 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (double rod, adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MICJ Adjustable Mini Cylinder MICJ16X75-75S Is Used
Package Diverting
Divert small cartons on a conveyor at high speed; the adjustable air cushion absorbs the end-of-stroke impact so the 5.1 kg load stops smoothly without bouncing.
Lab Dispensing Position
Set a precise lower travel limit for a liquid dispensing nozzle, relying on the -S magnet and DMSG sensor to confirm the adjusted extend position.
Is the Airtac MICJ Adjustable Mini Cylinder MICJ16X75-75S the Right Cylinder?
The Ø16 bore uses the ISO 6432 mini-cylinder mounting interface, dropping into standard mini brackets and clevises. You can use LB foot, FA flange, or TC trunnion mounts, but the SDB pivot-block is not available on this adjustable-stroke variant.
The external stop screw sets the extend end position but is not a mid-stroke lock. The cylinder does not hold a load on air loss—the piston drifts, and the cushion only decelerates near the stroke end. For a held load, install an external rod lock or a pilot-operated check valve.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MICJ Adjustable Mini Cylinder MICJ16X75-75S FAQ
This Ø16 bore cylinder uses an M5×0.8 port.
An external screw shortens the extend stroke by up to 75 mm, while a needle valve adjusts the air cushion at both ends to decelerate the piston. The stop screw is not a mid-stroke lock, and the cylinder will drift on air loss. The -S magnet enables CMSG, DMSG, or EMSG sensors.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC MICJ Cylinders
Request a Quote for Airtac MICJ Adjustable Mini Cylinder MICJ16X75-75S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.