Airtac MICJ Adjustable Mini Cylinder MICJ16X80-100
The AirTAC MICJ Adjustable Mini Cylinder MICJ16X80-100 is a genuine double acting, double rod, adjustable stroke + cushion round-body mini air cylinder with a Ø16mm bore and 80mm stroke, M5×0.8 air ports and a stainless-steel barrel and rod for mildly corrosive environments. Its ISO 6432 mounting interface fits standard ISO 6432 mini-cylinder mounting interfaces.
- BoreØ16 mm
- Stroke80 mm
- Port sizeM5×0.8
- Acting typeDouble acting, double rod, adjustable stroke + cushion
- Rod threadM6×1.0
- CushionVariable air cushion, both ends
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MICJ Adjustable Mini Cylinder MICJ16X80-100
Dial in a precise forward stop on the spot with the AirTAC MICJ16X80-100, a double-acting stainless-steel round-body mini cylinder. An external stop screw lets you shorten the extend end position by up to 100 mm on site, giving a usable forward range of 0-80 mm without swapping hardware. Adjustable air cushions at both ends soak up high-speed shock to protect your tooling, while the M5×0.8 port and M6x1.0 male rod thread drop right into standard ISO 6432 mini-cylinder brackets.
Note that this specific SKU lacks a magnet, so it cannot host CMSG, DMSG, or EMSG sensors without switching to the -S variant.
Airtac MICJ Adjustable Mini Cylinder MICJ16X80-100 Technical Specifications
| Model | Airtac MICJ Adjustable Mini Cylinder MICJ16X80-100 |
|---|---|
| Series | MICJ ISO 6432 mini cylinder |
| Bore size | Ø16 mm |
| Stroke | 80 mm |
| Acting type | Double acting, double rod, adjustable stroke + cushion |
| Port size | M5×0.8 |
| Rod thread | M6×1.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Variable air cushion, both ends |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G.
Theoretical Output Force (Ø16mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 86 N |
| 0.7 MPa | 121 N |
| Max (@1.0 MPa) | 18 kgf |
MIJ / MICJ are double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
Model Code: Airtac MICJ Adjustable Mini Cylinder MICJ16X80-100
| MICJ | ISO 6432 round-body mini cylinder (adjustable-stroke, variable cushion). |
|---|---|
| 16 | Bore size in mm. |
| ×80 | Stroke length in mm. |
| -100 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (double rod, adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MICJ Adjustable Mini Cylinder MICJ16X80-100 Is Used
Package Diverter
Pushes lightweight cartons on a line at high speed, relying on the adjustable air cushion to prevent end-stroke banging.
Compact Sorting Gate
Fits into tight ISO 6432 mini-cylinder spaces to deflect small electronic components, tuning the extend position on the fly.
Is the Airtac MICJ Adjustable Mini Cylinder MICJ16X80-100 the Right Cylinder?
When sizing this bore, step down to a bumper-only MIJ if you just need simple end-of-stroke contact, or step up to a Ø20 MICJ if you need the 157 N @0.5 MPa push force for heavier slides. The MICJ16X80-100 shines in fast set-position moves where the external screw dials in the exact extend stop and the needle-set cushion trims the end-of-stroke impact. Mount it using LB foot, FA flange, or TC trunnion brackets (the SDB pivot block is not offered on this adjustable variant). Remember that the stop screw and cushion only decelerate near the stroke end; they do not lock the piston. If you need to hold a vertical load against air loss, add an external rod lock or pilot check valve.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MICJ Adjustable Mini Cylinder MICJ16X80-100 FAQ
This Ø16 bore cylinder features an M5×0.8 port and an M6x1.0 male rod thread. The theoretical maximum force is 20.5 kgf at 1.0 MPa.
An external screw shortens the extend stroke by up to 100 mm (usable 0-80 mm), while needle valves adjust the air cushion at both ends to absorb high-speed shock. The cushion only decelerates and does not lock the piston; you need an external rod lock for load holding. Also, this non-S SKU lacks a magnet and cannot take sensors.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC MICJ Cylinders
Request a Quote for Airtac MICJ Adjustable Mini Cylinder MICJ16X80-100
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.