Airtac MICJ Adjustable Mini Cylinder MICJ16X80-30
The AirTAC MICJ Adjustable Mini Cylinder MICJ16X80-30 is a genuine double acting, double rod, adjustable stroke + cushion round-body mini air cylinder with a Ø16mm bore and 80mm stroke, M5×0.8 air ports and a stainless-steel barrel and rod for mildly corrosive environments. Its ISO 6432 mounting interface fits standard ISO 6432 mini-cylinder mounting interfaces.
- BoreØ16 mm
- Stroke80 mm
- Port sizeM5×0.8
- Acting typeDouble acting, double rod, adjustable stroke + cushion
- Rod threadM6×1.0
- CushionVariable air cushion, both ends
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MICJ Adjustable Mini Cylinder MICJ16X80-30
Tune the forward stop on site with the AirTAC MICJ16X80-30, a stainless-steel round-body mini cylinder that lets you shorten the extend stroke by up to 30 mm via an external screw. A needle-set adjustable air cushion at both ends soaks up high-speed shock, letting you set the position and control the impact simultaneously. This double-acting actuator uses the ISO 6432 mounting interface for straightforward bracket interchangeability.
Built with a corrosion-resistant stainless barrel and Ø6 mm rod, this 16 mm bore model pushes 100.5 N at 0.5 MPa. It features an M5×0.8 port and a male M6x1.0 rod thread. Note that this specific SKU lacks a magnet and cannot host CMSG, DMSG, or EMSG sensors.
Airtac MICJ Adjustable Mini Cylinder MICJ16X80-30 Technical Specifications
| Model | Airtac MICJ Adjustable Mini Cylinder MICJ16X80-30 |
|---|---|
| Series | MICJ ISO 6432 mini cylinder |
| Bore size | Ø16 mm |
| Stroke | 80 mm |
| Acting type | Double acting, double rod, adjustable stroke + cushion |
| Port size | M5×0.8 |
| Rod thread | M6×1.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Variable air cushion, both ends |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G.
Theoretical Output Force (Ø16mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 86 N |
| 0.7 MPa | 121 N |
| Max (@1.0 MPa) | 18 kgf |
MIJ / MICJ are double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
Model Code: Airtac MICJ Adjustable Mini Cylinder MICJ16X80-30
| MICJ | ISO 6432 round-body mini cylinder (adjustable-stroke, variable cushion). |
|---|---|
| 16 | Bore size in mm. |
| ×80 | Stroke length in mm. |
| -30 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (double rod, adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MICJ Adjustable Mini Cylinder MICJ16X80-30 Is Used
Sorting Diverter
Dial in the 30 mm extend stop to deflect small parts on a conveyor, using the dual air cushions to absorb the impact of rapid 100.5 N positioning moves.
Carton Flap Folder
Set a precise forward position to fold light cardboard flaps, relying on the adjustable stroke to fine-tune the reach without re-mounting the cylinder.
Lab Sample Ejector
Push test tubes out of a tray at high speed; the stainless build resists mild washdowns while the needle cushion decelerates the 80 mm stroke smoothly.
Is the Airtac MICJ Adjustable Mini Cylinder MICJ16X80-30 the Right Cylinder?
When sizing this 16 mm bore actuator, step down to an MIJ bumper-only cylinder if your load is lighter, or step up to a 20 mm MICJ bore (which pushes 157.0 N at 0.5 MPa) if you need more force. The 30 mm extend adjuster and dual air cushions shine in fast set-position moves where you must dial in a precise forward stop without swapping hardware. For mounting, choose LB foot, FA flange, or TC trunnion (SDB pivot-block is not available on this adjustable variant). Remember that the stop screw sets the end position but is not a mid-stroke lock; the piston will drift on air loss, so add an external rod lock or pilot check valve to hold a suspended load.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MICJ Adjustable Mini Cylinder MICJ16X80-30 FAQ
At 0.7 MPa, push is 140.7 N and pull is 120.9 N. The theoretical max force is 20.5 kgf at 1.0 MPa, and the air port size is M5×0.8.
An external screw shortens the extend stroke by up to 30 mm, while needle valves adjust the air cushions at both ends to decelerate high-speed moves. The cushion only slows the piston near the end of travel; it is not a brake. This SKU has no magnet for sensors, and the piston will drift on air loss, so use an external rod lock to hold a load.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC MICJ Cylinders
Request a Quote for Airtac MICJ Adjustable Mini Cylinder MICJ16X80-30
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.