Airtac MICJ Adjustable Mini Cylinder MICJ16X80-50
The AirTAC MICJ Adjustable Mini Cylinder MICJ16X80-50 is a genuine double acting, double rod, adjustable stroke + cushion round-body mini air cylinder with a Ø16mm bore and 80mm stroke, M5×0.8 air ports and a stainless-steel barrel and rod for mildly corrosive environments. Its ISO 6432 mounting interface fits standard ISO 6432 mini-cylinder mounting interfaces.
- BoreØ16 mm
- Stroke80 mm
- Port sizeM5×0.8
- Acting typeDouble acting, double rod, adjustable stroke + cushion
- Rod threadM6×1.0
- CushionVariable air cushion, both ends
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MICJ Adjustable Mini Cylinder MICJ16X80-50
Trim the forward stop by up to 50 mm on site without swapping cylinders, and let the adjustable air cushions at both ends soak up high-speed shock. This AirTAC MICJ16X80-50 is a double-acting, round-body stainless-steel mini cylinder with a nominal 80 mm stroke, yielding a usable extend range of 30-80 mm while retract remains full. The stainless barrel and Ø6 mm piston rod resist mild corrosion and washdown environments, and its mounting interface conforms to ISO 6432 for standard mini brackets.
Note this SKU lacks the -S magnet, so it cannot host CMSG, DMSG, or EMSG sensors.
Airtac MICJ Adjustable Mini Cylinder MICJ16X80-50 Technical Specifications
| Model | Airtac MICJ Adjustable Mini Cylinder MICJ16X80-50 |
|---|---|
| Series | MICJ ISO 6432 mini cylinder |
| Bore size | Ø16 mm |
| Stroke | 80 mm |
| Acting type | Double acting, double rod, adjustable stroke + cushion |
| Port size | M5×0.8 |
| Rod thread | M6×1.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Variable air cushion, both ends |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G.
Theoretical Output Force (Ø16mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 86 N |
| 0.7 MPa | 121 N |
| Max (@1.0 MPa) | 18 kgf |
MIJ / MICJ are double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
Model Code: Airtac MICJ Adjustable Mini Cylinder MICJ16X80-50
| MICJ | ISO 6432 round-body mini cylinder (adjustable-stroke, variable cushion). |
|---|---|
| 16 | Bore size in mm. |
| ×80 | Stroke length in mm. |
| -50 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (double rod, adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MICJ Adjustable Mini Cylinder MICJ16X80-50 Is Used
Package Diverting
Divert lightweight cartons on a washdown line where the stainless construction resists moisture, relying on the 5.1 kg vertical lift capacity to actuate the routing gate.
Sensor Probe Indexing
Index a testing probe against delicate electronics, setting the forward stop short of the full 80 mm to protect the part while maintaining rapid 30-800 mm/s cycling.
Is the Airtac MICJ Adjustable Mini Cylinder MICJ16X80-50 the Right Cylinder?
The external stop screw and dual needle cushions shine in fast set-position moves where you must dial in the forward end and control impact, but remember the screw only sets the end position—it is not a mid-stroke lock. The piston will drift on air loss, so fit an external rod lock or pilot check valve for held loads.
Mount using LB foot, FA flange, or TC trunnion brackets, or choose CA, U, R, or CM back covers; the SDB pivot-block is not available on this adjustable-stroke build. Because this specific SKU has no -S magnet, it cannot accept position sensors.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MICJ Adjustable Mini Cylinder MICJ16X80-50 FAQ
The theoretical maximum force is 20.5 kgf at 1.0 MPa.
An external screw shortens the extend stroke by up to 50 mm (retract stays full), while needle-set air cushions at both ends absorb high-speed shock. The stop screw sets the end position but is not a mid-stroke lock; the piston drifts on air loss, so use an external rod lock to hold a load. This non-S SKU lacks a magnet for sensors.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC MICJ Cylinders
Request a Quote for Airtac MICJ Adjustable Mini Cylinder MICJ16X80-50
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.