Airtac MICJ Adjustable Mini Cylinder MICJ16X80-75
The AirTAC MICJ Adjustable Mini Cylinder MICJ16X80-75 is a genuine double acting, double rod, adjustable stroke + cushion round-body mini air cylinder with a Ø16mm bore and 80mm stroke, M5×0.8 air ports and a stainless-steel barrel and rod for mildly corrosive environments. Its ISO 6432 mounting interface fits standard ISO 6432 mini-cylinder mounting interfaces.
- BoreØ16 mm
- Stroke80 mm
- Port sizeM5×0.8
- Acting typeDouble acting, double rod, adjustable stroke + cushion
- Rod threadM6×1.0
- CushionVariable air cushion, both ends
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MICJ Adjustable Mini Cylinder MICJ16X80-75
Dial in a precise forward stop on-site without swapping hardware using the AirTAC MICJ16X80-75. This double-acting, round-body stainless-steel mini cylinder features an external screw that shortens the extend stroke by up to 75 mm (usable extend 5-80 mm), paired with a needle-adjustable air cushion at both ends to soak up high-speed shock. The stainless barrel and Ø6 mm piston rod resist mild corrosion and washdown environments.
It conforms to the ISO 6432 mounting interface for standard mini brackets. Note that this specific SKU lacks a magnet, so it cannot host CMSG, DMSG, or EMSG sensors without upgrading to the -S variant.
Airtac MICJ Adjustable Mini Cylinder MICJ16X80-75 Technical Specifications
| Model | Airtac MICJ Adjustable Mini Cylinder MICJ16X80-75 |
|---|---|
| Series | MICJ ISO 6432 mini cylinder |
| Bore size | Ø16 mm |
| Stroke | 80 mm |
| Acting type | Double acting, double rod, adjustable stroke + cushion |
| Port size | M5×0.8 |
| Rod thread | M6×1.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Variable air cushion, both ends |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G.
Theoretical Output Force (Ø16mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 86 N |
| 0.7 MPa | 121 N |
| Max (@1.0 MPa) | 18 kgf |
MIJ / MICJ are double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
Model Code: Airtac MICJ Adjustable Mini Cylinder MICJ16X80-75
| MICJ | ISO 6432 round-body mini cylinder (adjustable-stroke, variable cushion). |
|---|---|
| 16 | Bore size in mm. |
| ×80 | Stroke length in mm. |
| -75 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (double rod, adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MICJ Adjustable Mini Cylinder MICJ16X80-75 Is Used
Package Diverting
Sorts light cartons on a line by extending a gate to a precise 40 mm position, using the adjustable stroke to dial in the exact deflection angle without moving the bracket.
Film Roll Tensioning
Maintains light tension on packaging web material, leveraging the 5.1 kg vertical lift margin and needle-set cushions to smooth out rapid direction changes.
Is the Airtac MICJ Adjustable Mini Cylinder MICJ16X80-75 the Right Cylinder?
If you need less power, the smaller MIJ series relies on a bumper rather than an air cushion. If your application exceeds this capacity, stepping up to the Ø20 bore raises the push force to 157 N. The adjustable stop screw and dual cushions shine in fast set-position moves where you must tune both the forward endpoint and the deceleration rate.
Remember that the stop screw sets the end position but is not a mid-stroke lock; the piston will drift on air loss, so add an external rod lock or pilot check valve for held loads. For mounting, use LB foot, FA flange, or TC trunnion brackets (SDB pivot-block is not available on this adjustable variant). Because this SKU has no magnet, position sensing is impossible here.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MICJ Adjustable Mini Cylinder MICJ16X80-75 FAQ
At 0.7 MPa, push is 140.7 N and pull is 120.9 N. The theoretical maximum force is 20.5 kgf at 1.0 MPa.
An external screw shortens the extend stroke by up to 75 mm on-site, while needle valves adjust the air cushions at both ends to decelerate the piston before impact. The cushions only slow the rod near stroke end and do not lock or hold the load; the piston drifts on air loss. This SKU also lacks a magnet, so it cannot support position sensors.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC MICJ Cylinders
Request a Quote for Airtac MICJ Adjustable Mini Cylinder MICJ16X80-75
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.