Airtac MICJ Adjustable Mini Cylinder MICJ16X90-20
The AirTAC MICJ Adjustable Mini Cylinder MICJ16X90-20 is a genuine double acting, double rod, adjustable stroke + cushion round-body mini air cylinder with a Ø16mm bore and 90mm stroke, M5×0.8 air ports and a stainless-steel barrel and rod for mildly corrosive environments. Its ISO 6432 mounting interface fits standard ISO 6432 mini-cylinder mounting interfaces.
- BoreØ16 mm
- Stroke90 mm
- Port sizeM5×0.8
- Acting typeDouble acting, double rod, adjustable stroke + cushion
- Rod threadM6×1.0
- CushionVariable air cushion, both ends
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MICJ Adjustable Mini Cylinder MICJ16X90-20
Trim the forward stop by up to 20 mm on site without swapping hardware using the AirTAC MICJ16X90-20. This ISO 6432 round-body stainless-steel mini cylinder pairs an external extend-stop screw with a needle-adjustable air cushion at both ends, letting you dial in the 70-90 mm forward position while soaking up high-speed impact. It operates at 30-800 mm/s and features an M5×0.8 port.
The stainless barrel and rod shrug off mild washdown corrosion. As a non-magnet SKU, it cannot host CMSG, DMSG, or EMSG sensors.
Airtac MICJ Adjustable Mini Cylinder MICJ16X90-20 Technical Specifications
| Model | Airtac MICJ Adjustable Mini Cylinder MICJ16X90-20 |
|---|---|
| Series | MICJ ISO 6432 mini cylinder |
| Bore size | Ø16 mm |
| Stroke | 90 mm |
| Acting type | Double acting, double rod, adjustable stroke + cushion |
| Port size | M5×0.8 |
| Rod thread | M6×1.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Variable air cushion, both ends |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G.
Theoretical Output Force (Ø16mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 86 N |
| 0.7 MPa | 121 N |
| Max (@1.0 MPa) | 18 kgf |
MIJ / MICJ are double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
Model Code: Airtac MICJ Adjustable Mini Cylinder MICJ16X90-20
| MICJ | ISO 6432 round-body mini cylinder (adjustable-stroke, variable cushion). |
|---|---|
| 16 | Bore size in mm. |
| ×90 | Stroke length in mm. |
| -20 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (double rod, adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MICJ Adjustable Mini Cylinder MICJ16X90-20 Is Used
Gate Diversion
Actuates a lightweight routing gate on a packaging line, relying on the adjustable air cushion to absorb shock during 800 mm/s high-speed cycles.
Lab Sample Indexing
Moves delicate test trays horizontally, setting a precise 75 mm forward stroke while the stainless body resists mild chemical corrosion.
Is the Airtac MICJ Adjustable Mini Cylinder MICJ16X90-20 the Right Cylinder?
The 20 mm extend adjuster and dual air cushions shine in fast set-position moves where you must tune the end point and decelerate smoothly. Mount via LB foot, FA flange, or TC trunnion (SDB pivot-block is unavailable). This SKU lacks a magnet, so position sensing requires the -S variant. Note that the stop screw sets the end position but is not a mid-stroke lock; the piston will drift on air loss, so add an external rod lock or pilot check valve for held loads.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MICJ Adjustable Mini Cylinder MICJ16X90-20 FAQ
This 16 mm bore cylinder uses an M5×0.8 port and an M6x1.0 male rod thread.
An external screw shortens the extend stroke by up to 20 mm (usable range 70-90 mm), while a needle valve adjusts the air cushion at both ends to decelerate high-speed impacts. The cushion only decelerates near the end and is not a brake; the cylinder drifts on air loss. This non-S SKU lacks a magnet, so it cannot take position sensors.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC MICJ Cylinders
Request a Quote for Airtac MICJ Adjustable Mini Cylinder MICJ16X90-20
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.