Airtac MICJ Adjustable Mini Cylinder MICJ40X175-100S
The AirTAC MICJ Adjustable Mini Cylinder MICJ40X175-100S is a genuine double acting, double rod, adjustable stroke + cushion round-body mini air cylinder with a Ø40mm bore and 175mm stroke, 1/4" air ports and a stainless-steel barrel and rod for mildly corrosive environments.
- BoreØ40 mm
- Stroke175 mm
- Port size1/4"
- Acting typeDouble acting, double rod, adjustable stroke + cushion
- Rod threadM12×1.25
- CushionVariable air cushion, both ends
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MICJ Adjustable Mini Cylinder MICJ40X175-100S
Trim the forward stop by up to 100 mm on site without swapping hardware using the AirTAC MICJ40X175-100S. This round-body stainless steel mini cylinder pairs a 1/4" port and M12x1.25 male rod thread with a needle-set variable air cushion at both ends to soak up high-speed shock.
Because the -S suffix includes a built-in piston magnet, you can mount CMSG, DMSG or EMSG sensors for position detection. The stainless barrel and rod resist mild washdown corrosion, and the external screw sets the extend end position only.
Airtac MICJ Adjustable Mini Cylinder MICJ40X175-100S Technical Specifications
| Model | Airtac MICJ Adjustable Mini Cylinder MICJ40X175-100S |
|---|---|
| Series | MICJ mini cylinder |
| Bore size | Ø40 mm |
| Stroke | 175 mm |
| Acting type | Double acting, double rod, adjustable stroke + cushion |
| Port size | 1/4" |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Variable air cushion, both ends |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G. Note: the Ø40 bore is a larger, non-ISO-6432 size.
Theoretical Output Force (Ø40mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 528 N |
| 0.7 MPa | 739 N |
| Max (@1.0 MPa) | 108 kgf |
MIJ / MICJ are double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
Model Code: Airtac MICJ Adjustable Mini Cylinder MICJ40X175-100S
| MICJ | round-body mini cylinder (adjustable-stroke, variable cushion). |
|---|---|
| 40 | Bore size in mm. |
| ×175 | Stroke length in mm. |
| -100 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (double rod, adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MICJ Adjustable Mini Cylinder MICJ40X175-100S Is Used
Pallet Deceleration
Stop large inbound pallets on a high-speed line, relying on the adjustable air cushion to absorb the kinetic energy smoothly.
Carton Flap Folding
Tuck heavy corrugated flaps at high cycle rates, tweaking the forward position by up to 100 mm to match varying box depths.
Is the Airtac MICJ Adjustable Mini Cylinder MICJ40X175-100S the Right Cylinder?
When sizing this 40 mm bore, stepping down to the 32 mm variant drops the 0.5 MPa push force to 402.2 N, while no larger ISO standard bore exists in this mini family. Choose this model when you need fast, repeatable set-position moves where the 100 mm extend adjuster and dual cushions prevent harsh end impacts.
Mount via LB foot, FA flange or TC trunnion, noting the SDB pivot-block is not offered on this adjustable variant. Remember that the stop screw and air cushion only decelerate near the stroke end; they do not act as a mid-stroke lock. If your application must hold a load on air loss, install an external rod lock or pilot-operated check valve.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MICJ Adjustable Mini Cylinder MICJ40X175-100S FAQ
An external screw shortens the extend stroke by up to 100 mm, giving a usable forward range of 75-175 mm, while the needle-set variable air cushion at both ends decelerates the piston to reduce shock. The -S magnet enables CMSG, DMSG or EMSG sensors for position feedback.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC MICJ Cylinders
Request a Quote for Airtac MICJ Adjustable Mini Cylinder MICJ40X175-100S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.