Airtac MICJ Adjustable Mini Cylinder MICJ40X60-30S
The AirTAC MICJ Adjustable Mini Cylinder MICJ40X60-30S is a genuine double acting, double rod, adjustable stroke + cushion round-body mini air cylinder with a Ø40mm bore and 60mm stroke, 1/4" air ports and a stainless-steel barrel and rod for mildly corrosive environments.
- BoreØ40 mm
- Stroke60 mm
- Port size1/4"
- Acting typeDouble acting, double rod, adjustable stroke + cushion
- Rod threadM12×1.25
- CushionVariable air cushion, both ends
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MICJ Adjustable Mini Cylinder MICJ40X60-30S
Cutting high-speed impact down to size, this AirTAC round-body mini cylinder pairs a needle-set adjustable air cushion at both ends with a 30 mm external stop screw that shortens the extend end position on-site. The stainless-steel barrel and Ø16 mm piston rod shrug off mild corrosion and washdown, while the 1/4" port feeds a robust 40 mm bore. Because this SKU includes the -S magnet, it is ready for CMSG, DMSG, or EMSG position switches.
With a nominal 60 mm stroke, the forward travel can be dialed back to a 30 mm minimum without swapping hardware. Operating pressure spans 0.15 to 1.0 MPa, and the male M12x1.25 rod thread secures your tooling firmly.
Airtac MICJ Adjustable Mini Cylinder MICJ40X60-30S Technical Specifications
| Model | Airtac MICJ Adjustable Mini Cylinder MICJ40X60-30S |
|---|---|
| Series | MICJ mini cylinder |
| Bore size | Ø40 mm |
| Stroke | 60 mm |
| Acting type | Double acting, double rod, adjustable stroke + cushion |
| Port size | 1/4" |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Variable air cushion, both ends |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G. Note: the Ø40 bore is a larger, non-ISO-6432 size.
Theoretical Output Force (Ø40mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 528 N |
| 0.7 MPa | 739 N |
| Max (@1.0 MPa) | 108 kgf |
MIJ / MICJ are double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
Model Code: Airtac MICJ Adjustable Mini Cylinder MICJ40X60-30S
| MICJ | round-body mini cylinder (adjustable-stroke, variable cushion). |
|---|---|
| 40 | Bore size in mm. |
| ×60 | Stroke length in mm. |
| -30 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (double rod, adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MICJ Adjustable Mini Cylinder MICJ40X60-30S Is Used
Heavy Clamping Press
Dial in the 30 mm extend stop to clamp 32 kg assemblies precisely, letting the dual air cushions absorb the high-speed impact without slamming the tooling.
Is the Airtac MICJ Adjustable Mini Cylinder MICJ40X60-30S the Right Cylinder?
When sizing this 40 mm bore, stepping down to a 32 mm variant drops the 0.5 MPa push force to 402.2 N, whereas no larger standard MICJ bore exists above this. The external stop screw and dual cushions shine in fast set-position moves where you must tune the forward landing and absorb shock without adding external shock absorbers. Mount using LB foot, FA flange, or TC trunnion brackets, as the SDB pivot-block is not offered on this adjustable-stroke build.
Remember that the stop screw sets the end position but acts purely as a forward stop, not a mid-stroke lock. If gravity or air loss could cause the piston to drift, install an external rod lock or pilot-operated check valve to hold the load safely.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MICJ Adjustable Mini Cylinder MICJ40X60-30S FAQ
The theoretical maximum force is 128.1 kgf at 1.0 MPa.
The external screw shortens the extend stroke by up to 30 mm (usable forward travel 30-60 mm), and the needle-set air cushions at both ends decelerate the piston near stroke ends. The -S magnet enables CMSG/DMSG/EMSG sensors, but the cushion and screw are not brakes; use an external rod lock to hold a load on air loss.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC MICJ Cylinders
Request a Quote for Airtac MICJ Adjustable Mini Cylinder MICJ40X60-30S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.