Airtac MICJ Adjustable Mini Cylinder MICJ40X60-40
The AirTAC MICJ Adjustable Mini Cylinder MICJ40X60-40 is a genuine double acting, double rod, adjustable stroke + cushion round-body mini air cylinder with a Ø40mm bore and 60mm stroke, 1/4" air ports and a stainless-steel barrel and rod for mildly corrosive environments.
- BoreØ40 mm
- Stroke60 mm
- Port size1/4"
- Acting typeDouble acting, double rod, adjustable stroke + cushion
- Rod threadM12×1.25
- CushionVariable air cushion, both ends
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MICJ Adjustable Mini Cylinder MICJ40X60-40
Dial in the forward stop without swapping cylinders: the AirTAC MICJ40X60-40 uses an external screw to shorten the extend end position by up to 40 mm on site, giving a usable forward range of 20-60 mm. This double-acting round-body mini cylinder pairs that on-site adjustability with a needle-set variable air cushion at both ends to soak up high-speed shock. The stainless-steel barrel and piston rod resist mild corrosion and washdown environments.
As the largest bore in the series, this Ø40 unit delivers serious force for a mini cylinder, pushing 628.3 N and pulling 527.8 N at 0.5 MPa. It features a 1/4" air port and an M12x1.25 male rod thread. Note this is a non-ISO-6432 size, and because this specific SKU lacks the -S magnet, it cannot accept CMSG, DMSG, or EMSG sensors.
Airtac MICJ Adjustable Mini Cylinder MICJ40X60-40 Technical Specifications
| Model | Airtac MICJ Adjustable Mini Cylinder MICJ40X60-40 |
|---|---|
| Series | MICJ mini cylinder |
| Bore size | Ø40 mm |
| Stroke | 60 mm |
| Acting type | Double acting, double rod, adjustable stroke + cushion |
| Port size | 1/4" |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Variable air cushion, both ends |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G. Note: the Ø40 bore is a larger, non-ISO-6432 size.
Theoretical Output Force (Ø40mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 528 N |
| 0.7 MPa | 739 N |
| Max (@1.0 MPa) | 108 kgf |
MIJ / MICJ are double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
Model Code: Airtac MICJ Adjustable Mini Cylinder MICJ40X60-40
| MICJ | round-body mini cylinder (adjustable-stroke, variable cushion). |
|---|---|
| 40 | Bore size in mm. |
| ×60 | Stroke length in mm. |
| -40 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (double rod, adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MICJ Adjustable Mini Cylinder MICJ40X60-40 Is Used
Heavy Part Clamping
Securely hold 30+ kg metal castings during machining, using the 40 mm extend adjustment to dial in the exact clamp distance without shimming.
Vertical Press Fit
Press bearings or pins into housings, using the adjustable forward stop to prevent over-travel and the 1/4" port to deliver high force.
Is the Airtac MICJ Adjustable Mini Cylinder MICJ40X60-40 the Right Cylinder?
When sizing this 40 mm bore, dropping down to the Ø32 model reduces the 0.5 MPa push force to 402.2 N, while no larger MICJ bore exists above it. The external stop screw and dual adjustable air cushions are perfect for fast, set-position moves where you must control both the exact endpoint and the impact deceleration.
Keep in mind that the stop screw sets the end position but is not a mid-stroke lock, and the air cushion only decelerates near the stroke end, never holding the load. If air pressure drops, the piston will drift, so add an external rod lock or pilot-operated check valve for suspended loads. For mounting, use LB foot, FA flange, or TC trunnion brackets, plus CA, U, R, or CM back covers, as the SDB pivot-block is not available on this adjustable-stroke variant.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MICJ Adjustable Mini Cylinder MICJ40X60-40 FAQ
This double-acting cylinder pushes 628.3 N and pulls 527.8 N at 0.5 MPa, and pushes 879.6 N / pulls 738.9 N at 0.7 MPa. The theoretical maximum force is 128.1 kgf at 1.0 MPa. It uses a 1/4" air port and a 16 mm piston rod with an M12x1.25 male thread.
An external screw shortens the extend stroke by up to 40 mm, letting you set the exact forward end position on site, while the needle-set variable air cushion at both ends decelerates the piston at high speed. The cushion only absorbs shock near the end of travel and does not lock or hold the load, so the piston will drift on air loss. Also, this SKU lacks a magnet, so it cannot take position sensors.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC MICJ Cylinders
Request a Quote for Airtac MICJ Adjustable Mini Cylinder MICJ40X60-40
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.