Airtac MIJ Adjustable Cylinder MIJ16X150-10S
The AirTAC MIJ Adjustable Cylinder MIJ16X150-10S is a genuine double acting, double rod, adjustable stroke round-body mini air cylinder with a Ø16mm bore and 150mm stroke, M5×0.8 air ports and a stainless-steel barrel and rod for mildly corrosive environments. Its ISO 6432 mounting interface fits standard ISO 6432 mini-cylinder mounting interfaces.
- BoreØ16 mm
- Stroke150 mm
- Port sizeM5×0.8
- Acting typeDouble acting, double rod, adjustable stroke
- Rod threadM6×1.0
- CushionFixed TPU bumper pads
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MIJ Adjustable Cylinder MIJ16X150-10S
Dial in a precise forward end position on-site with the AirTAC MIJ16X150-10S, a stainless-steel round-body mini cylinder. An external stop screw lets you trim the extend stroke by up to 10 mm (usable forward travel 140-150 mm) so one unit covers multiple stop lengths, while retract remains full. The built-in magnet (-S) supports CMSG, DMSG, and EMSG sensors for exact position detection.
The riveted stainless barrel and Ø6 mm rod shrug off mild washdown, and fixed TPU bumpers decelerate the stroke end across the 30-800 mm/s speed range.
Airtac MIJ Adjustable Cylinder MIJ16X150-10S Technical Specifications
| Model | Airtac MIJ Adjustable Cylinder MIJ16X150-10S |
|---|---|
| Series | MIJ ISO 6432 mini cylinder |
| Bore size | Ø16 mm |
| Stroke | 150 mm |
| Acting type | Double acting, double rod, adjustable stroke |
| Port size | M5×0.8 |
| Rod thread | M6×1.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Fixed TPU bumper pads |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G.
Theoretical Output Force (Ø16mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 86 N |
| 0.7 MPa | 121 N |
| Max (@1.0 MPa) | 18 kgf |
MIJ / MICJ are double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
Model Code: Airtac MIJ Adjustable Cylinder MIJ16X150-10S
| MIJ | ISO 6432 round-body mini cylinder (adjustable-stroke). |
|---|---|
| 16 | Bore size in mm. |
| ×150 | Stroke length in mm. |
| -10 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (double rod, adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MIJ Adjustable Cylinder MIJ16X150-10S Is Used
Calibrated Gauging Stops
Use the 10 mm extend adjustment to fine-tune a physical stop for checking part dimensions, providing a precise 60 N reference point that adapts to tolerance variations.
Changeover Diverter Arms
Shift a conveyor guide rail by dialing the forward stroke between 140 and 150 mm, using the 5.1 kg vertical lift capacity to reposition lightweight lane dividers quickly.
Staged Parts Ejection
Vary the ejection reach on a small press to clear different tooling profiles, relying on the stainless build and fixed TPU bumpers to handle repetitive cycling.
Is the Airtac MIJ Adjustable Cylinder MIJ16X150-10S the Right Cylinder?
When sizing this 16 mm bore, stepping down to a 12 mm bore drops the 0.5 MPa push force to 56.5 N, whereas stepping up to a 20 mm bore raises it to 157.0 N. The 10 mm external adjuster is ideal for taking up mechanical tolerances during setup or matching multiple part heights without swapping hardware. Mount using standard LB foot, FA flange, or TC trunnion brackets (the SDB pivot block is not offered on this adjustable variant). Remember the stop screw sets the forward end position; it is not a mid-stroke lock. If you need to hold a load on air loss, add an external rod lock or pilot check valve, as the piston will drift.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MIJ Adjustable Cylinder MIJ16X150-10S FAQ
This 16 mm bore cylinder features an M5×0.8 port and a Ø6 mm rod. The theoretical maximum force is 20.5 kgf at 1.0 MPa.
The external stop screw shortens the extend stroke by up to 10 mm on-site, but it only affects the forward end position; retract remains a full 150 mm. The -S suffix indicates a built-in piston magnet for use with CMSG, DMSG, or EMSG sensors. The screw is not a mid-stroke lock.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac MIJ Adjustable Cylinder MIJ16X150-10S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.