Airtac MIJ Adjustable Cylinder MIJ16X225-10
The AirTAC MIJ Adjustable Cylinder MIJ16X225-10 is a genuine double acting, double rod, adjustable stroke round-body mini air cylinder with a Ø16mm bore and 225mm stroke, M5×0.8 air ports and a stainless-steel barrel and rod for mildly corrosive environments. Its ISO 6432 mounting interface fits standard ISO 6432 mini-cylinder mounting interfaces.
- BoreØ16 mm
- Stroke225 mm
- Port sizeM5×0.8
- Acting typeDouble acting, double rod, adjustable stroke
- Rod threadM6×1.0
- CushionFixed TPU bumper pads
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MIJ Adjustable Cylinder MIJ16X225-10
Dial in a precise forward end position on-site with the AirTAC MIJ16X225-10, a double-acting round-body mini cylinder featuring a 10 mm external stop screw that shortens the extend stroke from its 225 mm nominal maximum down to 215 mm. Built with a stainless-steel barrel and piston rod, it handles mild washdown environments while conforming to the ISO 6432 mounting interface for straightforward bracket integration.
Fixed TPU bumper pads decelerate the piston at the stroke ends, and because this specific SKU lacks the -S magnet, it cannot host CMSG, DMSG, or EMSG sensors.
Airtac MIJ Adjustable Cylinder MIJ16X225-10 Technical Specifications
| Model | Airtac MIJ Adjustable Cylinder MIJ16X225-10 |
|---|---|
| Series | MIJ ISO 6432 mini cylinder |
| Bore size | Ø16 mm |
| Stroke | 225 mm |
| Acting type | Double acting, double rod, adjustable stroke |
| Port size | M5×0.8 |
| Rod thread | M6×1.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Fixed TPU bumper pads |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G.
Theoretical Output Force (Ø16mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 86 N |
| 0.7 MPa | 121 N |
| Max (@1.0 MPa) | 18 kgf |
MIJ / MICJ are double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
Model Code: Airtac MIJ Adjustable Cylinder MIJ16X225-10
| MIJ | ISO 6432 round-body mini cylinder (adjustable-stroke). |
|---|---|
| 16 | Bore size in mm. |
| ×225 | Stroke length in mm. |
| -10 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (double rod, adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MIJ Adjustable Cylinder MIJ16X225-10 Is Used
Changeover Sorting Gates
Quickly retune the 215 to 225 mm forward stop to handle different product lengths on a packaging line without swapping out the entire cylinder assembly.
Gentle Vertical Placement
Lower parts with a controlled stop using the fixed TPU bumpers, moving loads up to 5.1 kg safely before retracting the full 225 mm stroke.
Is the Airtac MIJ Adjustable Cylinder MIJ16X225-10 the Right Cylinder?
If you need less force, the smaller Ø12 bore provides 56.5 N; if your application demands more thrust, stepping up to the Ø20 bore yields 157.0 N. The 10 mm adjustment window is ideal for taking up mechanical tolerances during setup or covering slightly different part stops without changing the cylinder.
Remember that the stop screw only trims the extend end position—it is not a mid-stroke lock. The piston will drift if air pressure drops, so install an external pilot check valve or rod lock if you need to hold a load vertically. For mounting, you can use LB foot, FA flange, or TC trunnion brackets along with CA, U, R, or CM back covers, but the SDB pivot block is not available on this adjustable variant.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MIJ Adjustable Cylinder MIJ16X225-10 FAQ
At 0.7 MPa, push increases to 140.7 N and pull to 120.9 N. The theoretical maximum force is 20.5 kgf at 1.0 MPa.
An external stop screw shortens the extend stroke by up to 10 mm, letting you set the forward end position between 215 mm and 225 mm without affecting the full retract stroke. This specific SKU does not include a magnet, so it cannot support CMSG, DMSG, or EMSG sensors—you would need the -S variant for position sensing.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac MIJ Adjustable Cylinder MIJ16X225-10
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.