Airtac MIJ Adjustable Cylinder MIJ16X25-10
The AirTAC MIJ Adjustable Cylinder MIJ16X25-10 is a genuine double acting, double rod, adjustable stroke round-body mini air cylinder with a Ø16mm bore and 25mm stroke, M5×0.8 air ports and a stainless-steel barrel and rod for mildly corrosive environments. Its ISO 6432 mounting interface fits standard ISO 6432 mini-cylinder mounting interfaces.
- BoreØ16 mm
- Stroke25 mm
- Port sizeM5×0.8
- Acting typeDouble acting, double rod, adjustable stroke
- Rod threadM6×1.0
- CushionFixed TPU bumper pads
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MIJ Adjustable Cylinder MIJ16X25-10
Dial in your forward end position on-site with the AirTAC MIJ16X25-10, a round-body stainless-steel mini cylinder that lets an external stop screw shorten the extend stroke by up to 10 mm.
Built with a stainless barrel and rod for mild washdown resistance, it conforms to the ISO 6432 mounting interface for Ø16 bores and uses an M5×0.8 port with an M6x1.0 male rod thread. Fixed TPU bumper pads decelerate the stroke ends, while the lack of a magnet on this SKU means it cannot host CMSG, DMSG or EMSG sensors.
Airtac MIJ Adjustable Cylinder MIJ16X25-10 Technical Specifications
| Model | Airtac MIJ Adjustable Cylinder MIJ16X25-10 |
|---|---|
| Series | MIJ ISO 6432 mini cylinder |
| Bore size | Ø16 mm |
| Stroke | 25 mm |
| Acting type | Double acting, double rod, adjustable stroke |
| Port size | M5×0.8 |
| Rod thread | M6×1.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Fixed TPU bumper pads |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G.
Theoretical Output Force (Ø16mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 86 N |
| 0.7 MPa | 121 N |
| Max (@1.0 MPa) | 18 kgf |
MIJ / MICJ are double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
Model Code: Airtac MIJ Adjustable Cylinder MIJ16X25-10
| MIJ | ISO 6432 round-body mini cylinder (adjustable-stroke). |
|---|---|
| 16 | Bore size in mm. |
| ×25 | Stroke length in mm. |
| -10 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (double rod, adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MIJ Adjustable Cylinder MIJ16X25-10 Is Used
Gauge Positioning Stops
Trim the forward stroke by up to 10 mm to set exact contact depth for testing gauges, accommodating material thickness variations without retooling.
Staged Feed Pusher
Push lightweight components into a staging area with a 5.1 kg safe lift capacity, dialing the extend position inward to prevent crushing delicate parts.
Is the Airtac MIJ Adjustable Cylinder MIJ16X25-10 the Right Cylinder?
When sizing this 16 mm bore, dropping down to an MIJ12 lowers the 0.5 MPa push force to 56.5 N, whereas stepping up to an MIJ20 raises it to 157.0 N. The 10 mm external adjuster is ideal for taking up mechanical tolerances during setup, letting one part number cover several intermediate stops without swapping hardware. Mount using LB foot, FA flange or TC trunnion brackets, noting the SDB pivot block is not available on this adjustable variant.
Keep in mind the stop screw sets the end position but acts as no mid-stroke lock. If air pressure drops, the piston will drift, so fit an external rod lock or pilot check valve for suspended loads. To add position sensing, select the -S magnet version to enable switches.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MIJ Adjustable Cylinder MIJ16X25-10 FAQ
This 16 mm bore cylinder features an M5×0.8 port and an M6x1.0 male rod thread. The theoretical maximum force is 20.5 kgf at 1.0 MPa.
An external stop screw shortens the extend stroke by up to 10 mm on-site, while retract remains full. The screw sets the forward end position but is not a mid-stroke lock, and the piston will drift on air loss. This non-S SKU lacks a magnet, so it cannot host sensors.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac MIJ Adjustable Cylinder MIJ16X25-10
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.