Airtac MIJ Adjustable Cylinder MIJ16X25-10S
The AirTAC MIJ Adjustable Cylinder MIJ16X25-10S is a genuine double acting, double rod, adjustable stroke round-body mini air cylinder with a Ø16mm bore and 25mm stroke, M5×0.8 air ports and a stainless-steel barrel and rod for mildly corrosive environments. Its ISO 6432 mounting interface fits standard ISO 6432 mini-cylinder mounting interfaces.
- BoreØ16 mm
- Stroke25 mm
- Port sizeM5×0.8
- Acting typeDouble acting, double rod, adjustable stroke
- Rod threadM6×1.0
- CushionFixed TPU bumper pads
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MIJ Adjustable Cylinder MIJ16X25-10S
Dial in a precise forward end position on the fly with the AirTAC MIJ16X25-10S, a double-acting round-body mini cylinder featuring a 10 mm external stop screw that shortens the extend stroke from its 25 mm nominal length. Built with a stainless-steel barrel and piston rod, this riveted construction handles mild corrosion and routine washdowns while conforming to the ISO 6432 mounting interface for straightforward bracket integration.
Because this SKU includes the -S magnet, it is fully ready for CMSG, DMSG, or EMSG position sensing.
Airtac MIJ Adjustable Cylinder MIJ16X25-10S Technical Specifications
| Model | Airtac MIJ Adjustable Cylinder MIJ16X25-10S |
|---|---|
| Series | MIJ ISO 6432 mini cylinder |
| Bore size | Ø16 mm |
| Stroke | 25 mm |
| Acting type | Double acting, double rod, adjustable stroke |
| Port size | M5×0.8 |
| Rod thread | M6×1.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Fixed TPU bumper pads |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G.
Theoretical Output Force (Ø16mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 86 N |
| 0.7 MPa | 121 N |
| Max (@1.0 MPa) | 18 kgf |
MIJ / MICJ are double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
Model Code: Airtac MIJ Adjustable Cylinder MIJ16X25-10S
| MIJ | ISO 6432 round-body mini cylinder (adjustable-stroke). |
|---|---|
| 16 | Bore size in mm. |
| ×25 | Stroke length in mm. |
| -10 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (double rod, adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MIJ Adjustable Cylinder MIJ16X25-10S Is Used
Gauge Positioning Stops
Use the 10 mm extend adjuster to set a precise 20 mm forward stop for a mechanical gauge, accommodating part variances without swapping cylinders.
Staged Feed Ejection
Eject nested components at a staged intermediate position, dialing the forward end point in 1 mm increments to sync with an upstream feeder.
Is the Airtac MIJ Adjustable Cylinder MIJ16X25-10S the Right Cylinder?
The 10 mm external stop screw is invaluable for taking up mechanical tolerances during setup or covering multiple stop points with a single part number. Just remember the adjuster trims the extend end only and the retract stroke remains full.
This model uses fixed TPU bumper pads to decelerate the stroke end rather than an adjustable air cushion. It does not hold position on air loss, so the piston will drift if pressure drops—add an external rod lock or pilot check valve for suspended loads. Mounting options include LB foot, FA flange, and TC trunnion brackets, plus CA, U, R, or CM back covers, but the SDB pivot block is not offered on this adjustable variant.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MIJ Adjustable Cylinder MIJ16X25-10S FAQ
Its theoretical maximum force is 20.5 kgf at 1.0 MPa.
An external stop screw shortens the extend stroke by up to 10 mm on-site, letting you set the exact forward position without changing the cylinder; the retract stroke remains full. The -S suffix means it has a built-in piston magnet for CMSG, DMSG, or EMSG sensors.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac MIJ Adjustable Cylinder MIJ16X25-10S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.