Airtac MIJ Adjustable Cylinder MIJ16X30-10
The AirTAC MIJ Adjustable Cylinder MIJ16X30-10 is a genuine double acting, double rod, adjustable stroke round-body mini air cylinder with a Ø16mm bore and 30mm stroke, M5×0.8 air ports and a stainless-steel barrel and rod for mildly corrosive environments. Its ISO 6432 mounting interface fits standard ISO 6432 mini-cylinder mounting interfaces.
- BoreØ16 mm
- Stroke30 mm
- Port sizeM5×0.8
- Acting typeDouble acting, double rod, adjustable stroke
- Rod threadM6×1.0
- CushionFixed TPU bumper pads
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MIJ Adjustable Cylinder MIJ16X30-10
Dial in a precise forward end position on-site with the AirTAC MIJ16X30-10, a round-body stainless steel mini cylinder built for double-acting operation. An external stop screw lets you shorten the extend stroke by up to 10 mm, yielding a usable 20-30 mm forward travel without swapping parts. Retract remains at the full 30 mm. The riveted stainless barrel and Ø6 mm rod shrug off mild washdown environments.
It conforms to the ISO 6432 mounting interface for standard mini brackets. Piped via an M5×0.8 port, it runs at 30-800 mm/s and relies on fixed TPU bumper pads to decelerate the stroke end.
Airtac MIJ Adjustable Cylinder MIJ16X30-10 Technical Specifications
| Model | Airtac MIJ Adjustable Cylinder MIJ16X30-10 |
|---|---|
| Series | MIJ ISO 6432 mini cylinder |
| Bore size | Ø16 mm |
| Stroke | 30 mm |
| Acting type | Double acting, double rod, adjustable stroke |
| Port size | M5×0.8 |
| Rod thread | M6×1.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Fixed TPU bumper pads |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G.
Theoretical Output Force (Ø16mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 86 N |
| 0.7 MPa | 121 N |
| Max (@1.0 MPa) | 18 kgf |
MIJ / MICJ are double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
Model Code: Airtac MIJ Adjustable Cylinder MIJ16X30-10
| MIJ | ISO 6432 round-body mini cylinder (adjustable-stroke). |
|---|---|
| 16 | Bore size in mm. |
| ×30 | Stroke length in mm. |
| -10 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (double rod, adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MIJ Adjustable Cylinder MIJ16X30-10 Is Used
Light Clamping Fixtures
Apply a safe 60 N clamping force to delicate workpieces, using the 10 mm stroke adjuster to dial in the exact contact point without crushing the part.
Is the Airtac MIJ Adjustable Cylinder MIJ16X30-10 the Right Cylinder?
When sizing this unit, stepping down to a Ø12 bore drops the 0.5 MPa push force to 56.5 N, while stepping up to a Ø20 bore raises it to 157.0 N. The 10 mm external adjuster is highly useful for taking up mechanical tolerances during initial setup or accommodating slight part variations on a changeover job. You can mount via LB foot, FA flange, or TC trunnion, but note the SDB pivot block is not offered on this adjustable variant.
Because this SKU lacks the -S magnet, it cannot accept CMSG, DMSG, or EMSG sensors. Furthermore, the stop screw only sets the end position; it is not a mid-stroke lock. The piston will drift on air loss, so fit an external rod lock or pilot check valve if you need to hold a suspended load.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MIJ Adjustable Cylinder MIJ16X30-10 FAQ
The theoretical maximum force is 20.5 kgf at 1.0 MPa.
An external screw shortens the extend stroke by up to 10 mm (retract stays full). This SKU has no magnet (-S is required for CMSG/DMSG/EMSG sensors). The stainless build resists mild corrosion, and fixed TPU bumpers cushion the stroke end.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac MIJ Adjustable Cylinder MIJ16X30-10
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.