Airtac MIJ Adjustable Cylinder MIJ16X30-10S
The AirTAC MIJ Adjustable Cylinder MIJ16X30-10S is a genuine double acting, double rod, adjustable stroke round-body mini air cylinder with a Ø16mm bore and 30mm stroke, M5×0.8 air ports and a stainless-steel barrel and rod for mildly corrosive environments. Its ISO 6432 mounting interface fits standard ISO 6432 mini-cylinder mounting interfaces.
- BoreØ16 mm
- Stroke30 mm
- Port sizeM5×0.8
- Acting typeDouble acting, double rod, adjustable stroke
- Rod threadM6×1.0
- CushionFixed TPU bumper pads
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MIJ Adjustable Cylinder MIJ16X30-10S
Trimming the forward end by up to 10 mm on site, this adjustable-stroke mini cylinder lets you dial in the exact extend position without swapping parts. The external stop screw shortens the 30 mm extend stroke only; retract remains full.
Built as a double-acting, round-body unit with a stainless-steel barrel and rod, it handles mild washdown environments. The Ø16 bore conforms to the ISO 6432 mounting interface, accepting standard mini brackets. Air connects via an M5×0.8 port, and the -S suffix means a piston magnet is installed for CMSG, DMSG or EMSG sensors. Fixed TPU bumper pads decelerate the stroke ends.
Airtac MIJ Adjustable Cylinder MIJ16X30-10S Technical Specifications
| Model | Airtac MIJ Adjustable Cylinder MIJ16X30-10S |
|---|---|
| Series | MIJ ISO 6432 mini cylinder |
| Bore size | Ø16 mm |
| Stroke | 30 mm |
| Acting type | Double acting, double rod, adjustable stroke |
| Port size | M5×0.8 |
| Rod thread | M6×1.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Fixed TPU bumper pads |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G.
Theoretical Output Force (Ø16mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 86 N |
| 0.7 MPa | 121 N |
| Max (@1.0 MPa) | 18 kgf |
MIJ / MICJ are double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
Model Code: Airtac MIJ Adjustable Cylinder MIJ16X30-10S
| MIJ | ISO 6432 round-body mini cylinder (adjustable-stroke). |
|---|---|
| 16 | Bore size in mm. |
| ×30 | Stroke length in mm. |
| -10 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (double rod, adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MIJ Adjustable Cylinder MIJ16X30-10S Is Used
Tooling Clamp Adjustment
Dial in the exact 20-30 mm extend reach for a 60 N clamping fixture, absorbing part tolerances without machining new stops.
Staged Part Diverter
Fine-tune the pusher stroke on a washdown-resistant stainless rod to deflect packages gently without over-travel.
Sensor Bracket Positioning
Set a precise forward limit for a 5 kg test probe block, using the external screw to calibrate the exact touch point.
Is the Airtac MIJ Adjustable Cylinder MIJ16X30-10S the Right Cylinder?
The 10 mm adjust window is ideal for taking up mechanical tolerances during setup or covering multiple stop positions with one SKU. Remember the stop screw sets the end position but is not a mid-stroke lock; the piston will drift on air loss, so fit an external rod lock or pilot check valve to hold a load. Mount via LB foot, FA flange or TC trunnion (SDB is unavailable here), and pair the -S magnet with your chosen CMSG/DMSG/EMSG switch.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MIJ Adjustable Cylinder MIJ16X30-10S FAQ
This Ø16 bore cylinder features an M5×0.8 port and a Ø6 mm rod. The theoretical maximum force is 20.5 kgf at 1.0 MPa.
An external stop screw shortens the extend stroke by up to 10 mm on site, while retract stays full. The -S suffix indicates a built-in piston magnet for CMSG, DMSG or EMSG sensors. Fixed TPU bumpers absorb end impacts; it is not a mid-stroke lock.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac MIJ Adjustable Cylinder MIJ16X30-10S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.