Airtac MIJ Adjustable Cylinder MIJ16X30-10STC
The AirTAC MIJ Adjustable Cylinder MIJ16X30-10STC is a genuine double acting, double rod, adjustable stroke round-body mini air cylinder with a Ø16mm bore and 30mm stroke, M5×0.8 air ports and a stainless-steel barrel and rod for mildly corrosive environments. Its ISO 6432 mounting interface fits standard ISO 6432 mini-cylinder mounting interfaces.
- BoreØ16 mm
- Stroke30 mm
- Port sizeM5×0.8
- Acting typeDouble acting, double rod, adjustable stroke
- Rod threadM6×1.0
- CushionFixed TPU bumper pads
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MIJ Adjustable Cylinder MIJ16X30-10STC
Dial in a precise forward end position on-site with the AirTAC MIJ16X30-10STC, a round-body stainless steel mini cylinder built for double-acting operation. An external stop screw lets you shorten the extend stroke by up to 10 mm, yielding a usable forward travel of 20 to 30 mm without swapping parts. Retract travel remains at the full 30 mm. The fixed TPU bumper pads decelerate the piston near the stroke ends.
The stainless barrel and rod resist mild corrosion and washdown environments. It features an M5×0.8 port, an M6x1.0 male rod thread, and a built-in magnet for CMSG/DMSG/EMSG sensors.
Airtac MIJ Adjustable Cylinder MIJ16X30-10STC Technical Specifications
| Model | Airtac MIJ Adjustable Cylinder MIJ16X30-10STC |
|---|---|
| Series | MIJ ISO 6432 mini cylinder |
| Bore size | Ø16 mm |
| Stroke | 30 mm |
| Acting type | Double acting, double rod, adjustable stroke |
| Port size | M5×0.8 |
| Rod thread | M6×1.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Fixed TPU bumper pads |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G.
Theoretical Output Force (Ø16mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 86 N |
| 0.7 MPa | 121 N |
| Max (@1.0 MPa) | 18 kgf |
MIJ / MICJ are double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
Model Code: Airtac MIJ Adjustable Cylinder MIJ16X30-10STC
| MIJ | ISO 6432 round-body mini cylinder (adjustable-stroke). |
|---|---|
| 16 | Bore size in mm. |
| ×30 | Stroke length in mm. |
| -10 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (double rod, adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MIJ Adjustable Cylinder MIJ16X30-10STC Is Used
Precision Gauging Stops
Use the 10 mm extend adjustment to fine-tune the contact point for parts inspection, applying a safe 60 N working load to verify dimensions without damaging the workpiece.
Changeover Pushers
Quickly reconfigure the forward stop for new batch runs without changing cylinders, leveraging the 5.1 kg vertical lift capacity to position cartons accurately.
Is the Airtac MIJ Adjustable Cylinder MIJ16X30-10STC the Right Cylinder?
The integrated 10 mm stop screw on this 16 mm bore is invaluable for taking up mechanical tolerances during setup or staging feeds, letting one part number cover several intermediate stops. The stop screw sets the end position but is not a mid-stroke lock; the piston will drift on air loss, so fit an external rod lock or pilot check valve for held loads. You can mount this unit via the TC trunnion or standard LB/FA brackets, but note the SDB pivot-block is not available on this adjustable variant.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MIJ Adjustable Cylinder MIJ16X30-10STC FAQ
The theoretical maximum force is 20.5 kgf at 1.0 MPa.
The external stop screw shortens the extend stroke by up to 10 mm (usable forward travel 20-30 mm); retract remains full stroke. The built-in -S magnet allows CMSG/DMSG/EMSG switches to detect piston position, while the stainless construction resists mild corrosion.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac MIJ Adjustable Cylinder MIJ16X30-10STC
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.