Airtac MIJ Adjustable Cylinder MIJ16X30-30S
The AirTAC MIJ Adjustable Cylinder MIJ16X30-30S is a genuine double acting, double rod, adjustable stroke round-body mini air cylinder with a Ø16mm bore and 30mm stroke, M5×0.8 air ports and a stainless-steel barrel and rod for mildly corrosive environments. Its ISO 6432 mounting interface fits standard ISO 6432 mini-cylinder mounting interfaces.
- BoreØ16 mm
- Stroke30 mm
- Port sizeM5×0.8
- Acting typeDouble acting, double rod, adjustable stroke
- Rod threadM6×1.0
- CushionFixed TPU bumper pads
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MIJ Adjustable Cylinder MIJ16X30-30S
Dial in the exact forward end position on-site with the AirTAC MIJ16X30-30S, a double-acting round-body mini cylinder featuring a 30 mm adjustable extend stroke. An external stop screw lets you shorten the forward travel anywhere from 0 to 30 mm without swapping parts, while retract remains full. The stainless-steel barrel and riveted construction shrug off mild corrosion and washdown environments.
It uses the ISO 6432 mounting interface for easy bracket drops, breathes through an M5×0.8 port, and includes a built-in piston magnet (-S) for CMSG, DMSG or EMSG sensors. Fixed TPU bumpers decelerate the stroke ends across the 30-800 mm/s speed range.
Airtac MIJ Adjustable Cylinder MIJ16X30-30S Technical Specifications
| Model | Airtac MIJ Adjustable Cylinder MIJ16X30-30S |
|---|---|
| Series | MIJ ISO 6432 mini cylinder |
| Bore size | Ø16 mm |
| Stroke | 30 mm |
| Acting type | Double acting, double rod, adjustable stroke |
| Port size | M5×0.8 |
| Rod thread | M6×1.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Fixed TPU bumper pads |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G.
Theoretical Output Force (Ø16mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 86 N |
| 0.7 MPa | 121 N |
| Max (@1.0 MPa) | 18 kgf |
MIJ / MICJ are double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
Model Code: Airtac MIJ Adjustable Cylinder MIJ16X30-30S
| MIJ | ISO 6432 round-body mini cylinder (adjustable-stroke). |
|---|---|
| 16 | Bore size in mm. |
| ×30 | Stroke length in mm. |
| -30 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (double rod, adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MIJ Adjustable Cylinder MIJ16X30-30S Is Used
Changeover Dial-In
Swap product families and use the 30 mm extend adjuster to fine-tune the forward stop for different carton sizes, absorbing mechanical tolerances without machining new spacers.
Sensor-Verified Press
Leverage the -S magnet with a DMSG switch to confirm end-of-stroke on a 5.1 kg vertical lift, tweaking the 0-30 mm extend window to set the exact contact depth without reprogramming.
Is the Airtac MIJ Adjustable Cylinder MIJ16X30-30S the Right Cylinder?
If your setup needs less push, the smaller MIJ12 bore provides 56.5 N at 0.5 MPa; stepping up to the MIJ20 yields 157.0 N for heavier stages. The 30 mm adjust window is ideal for taking up mechanical tolerances during changeovers, letting one cylinder cover multiple intermediate stop points. Because the stop screw only trims the extend end, retract always hits the full 30 mm.
Remember that the adjuster sets the end position but acts as no mid-stroke lock; the piston will drift if air pressure drops, so fit an external rod lock or pilot check valve for held loads. Mount via LB foot, FA flange or TC trunnion (SDB pivot block is not offered on this adjustable variant). The -S magnet enables position sensing, whereas a non-S SKU cannot take a sensor.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MIJ Adjustable Cylinder MIJ16X30-30S FAQ
This 16 mm bore cylinder uses an M5×0.8 air port. At 0.5 MPa it pushes 100.5 N and pulls 86.4 N. At 0.7 MPa it pushes 140.7 N and pulls 120.9 N. The theoretical maximum force is 20.5 kgf at 1.0 MPa.
The external stop screw shortens the extend stroke by up to 30 mm on-site; the retract stroke remains fixed at the full 30 mm. The -S suffix means a piston magnet is built-in for CMSG, DMSG or EMSG sensors. Fixed TPU bumpers decelerate the stroke ends.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac MIJ Adjustable Cylinder MIJ16X30-30S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.