Airtac MIJ Adjustable Cylinder MIJ16X35-20S
The AirTAC MIJ Adjustable Cylinder MIJ16X35-20S is a genuine double acting, double rod, adjustable stroke round-body mini air cylinder with a Ø16mm bore and 35mm stroke, M5×0.8 air ports and a stainless-steel barrel and rod for mildly corrosive environments. Its ISO 6432 mounting interface fits standard ISO 6432 mini-cylinder mounting interfaces.
- BoreØ16 mm
- Stroke35 mm
- Port sizeM5×0.8
- Acting typeDouble acting, double rod, adjustable stroke
- Rod threadM6×1.0
- CushionFixed TPU bumper pads
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MIJ Adjustable Cylinder MIJ16X35-20S
Dial in a precise forward end position on-site with the AirTAC MIJ16X35-20S, a round-body stainless steel mini cylinder featuring a 20 mm extend-stroke adjustment window. By turning the external stop screw, you can shorten the forward stroke anywhere from the nominal 35 mm down to 15 mm, allowing one part number to cover multiple stop distances without swapping hardware. The retract stroke remains full length, and the screw strictly sets the end position rather than acting as a mid-stroke lock.
The M5×0.8 port and M6x1.0 male rod thread facilitate straightforward integration, while the included -S piston magnet enables CMSG, DMSG, or EMSG sensor switches for position confirmation.
Airtac MIJ Adjustable Cylinder MIJ16X35-20S Technical Specifications
| Model | Airtac MIJ Adjustable Cylinder MIJ16X35-20S |
|---|---|
| Series | MIJ ISO 6432 mini cylinder |
| Bore size | Ø16 mm |
| Stroke | 35 mm |
| Acting type | Double acting, double rod, adjustable stroke |
| Port size | M5×0.8 |
| Rod thread | M6×1.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Fixed TPU bumper pads |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G.
Theoretical Output Force (Ø16mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 86 N |
| 0.7 MPa | 121 N |
| Max (@1.0 MPa) | 18 kgf |
MIJ / MICJ are double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
Model Code: Airtac MIJ Adjustable Cylinder MIJ16X35-20S
| MIJ | ISO 6432 round-body mini cylinder (adjustable-stroke). |
|---|---|
| 16 | Bore size in mm. |
| ×35 | Stroke length in mm. |
| -20 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (double rod, adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MIJ Adjustable Cylinder MIJ16X35-20S Is Used
Staged Diverting
Set the forward stroke between 15 and 35 mm to deflect lightweight cartons on a line, easily changing the stop distance for different product changeovers.
Is the Airtac MIJ Adjustable Cylinder MIJ16X35-20S the Right Cylinder?
When sizing this 16 mm bore, compare your thrust requirements both ways: stepping down to an MIJ12 drops the 0.5 MPa push force to 56.5 N, while stepping up to an MIJ20 increases it to 157.0 N. The 20 mm external adjustment is ideal for taking up mechanical tolerances during setup or staging feeds, saving you from machining custom spacers. Remember that the fixed TPU bumper pads decelerate the stroke end but do not lock the rod; if you need to hold a vertical load against air loss, add an external pilot check valve or rod lock. For mounting, you can use standard LB foot, FA flange, or TC trunnion brackets (the SDB pivot block is not offered on this adjustable variant), and the -S magnet version is required if you intend to use sensors.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MIJ Adjustable Cylinder MIJ16X35-20S FAQ
At 0.7 MPa, push increases to 140.7 N and pull to 120.9 N. The theoretical maximum force is 20.5 kgf at 1.0 MPa, and the air port size is M5×0.8.
An external stop screw shortens the extend stroke by up to 20 mm on-site, letting you set the forward end position between 15 and 35 mm; the retract stroke remains fixed. The -S suffix indicates a built-in piston magnet, allowing you to mount CMSG, DMSG, or EMSG sensors for position detection.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac MIJ Adjustable Cylinder MIJ16X35-20S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.