Airtac MIJ Adjustable Cylinder MIJ16X50-30S
The AirTAC MIJ Adjustable Cylinder MIJ16X50-30S is a genuine double acting, double rod, adjustable stroke round-body mini air cylinder with a Ø16mm bore and 50mm stroke, M5×0.8 air ports and a stainless-steel barrel and rod for mildly corrosive environments. Its ISO 6432 mounting interface fits standard ISO 6432 mini-cylinder mounting interfaces.
- BoreØ16 mm
- Stroke50 mm
- Port sizeM5×0.8
- Acting typeDouble acting, double rod, adjustable stroke
- Rod threadM6×1.0
- CushionFixed TPU bumper pads
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MIJ Adjustable Cylinder MIJ16X50-30S
Dial in a precise forward end position on-site with the AirTAC MIJ16X50-30S, a double-acting round-body mini cylinder featuring a 30mm adjustable extend window. An external stop screw lets you shorten the forward stroke from its 50mm nominal length down to 20mm, absorbing setup tolerances without swapping hardware. The retract stroke remains full length. Built with a stainless-steel barrel and piston rod, the riveted construction resists mild corrosion and washdown environments.
The M5×0.8 port and M6x1.0 male rod thread drop directly into standard ISO 6432 mini-cylinder mounting interfaces. Equipped with the -S magnet, it supports CMSG, DMSG, and EMSG position sensing. Fixed TPU bumper pads decelerate the stroke ends across a 30-800 mm/s speed range.
Airtac MIJ Adjustable Cylinder MIJ16X50-30S Technical Specifications
| Model | Airtac MIJ Adjustable Cylinder MIJ16X50-30S |
|---|---|
| Series | MIJ ISO 6432 mini cylinder |
| Bore size | Ø16 mm |
| Stroke | 50 mm |
| Acting type | Double acting, double rod, adjustable stroke |
| Port size | M5×0.8 |
| Rod thread | M6×1.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Fixed TPU bumper pads |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G.
Theoretical Output Force (Ø16mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 86 N |
| 0.7 MPa | 121 N |
| Max (@1.0 MPa) | 18 kgf |
MIJ / MICJ are double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
Model Code: Airtac MIJ Adjustable Cylinder MIJ16X50-30S
| MIJ | ISO 6432 round-body mini cylinder (adjustable-stroke). |
|---|---|
| 16 | Bore size in mm. |
| ×50 | Stroke length in mm. |
| -30 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (double rod, adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MIJ Adjustable Cylinder MIJ16X50-30S Is Used
Staged Feed Diverter
Route different carton sizes on a packing line by tweaking the forward stop position on the fly, leveraging the 5.1 kg vertical lift capacity to push items cleanly off the belt.
Sensor-Verified Insertion
Press bearings into housings to precise depths using the adjustable end stop, relying on the -S magnet and a DMSG switch to confirm the extend position before the press cycle completes.
Is the Airtac MIJ Adjustable Cylinder MIJ16X50-30S the Right Cylinder?
The 30mm external adjuster is ideal for changeover jobs where you need one part number to cover several staged stops, letting you fine-tune the extend end without machining new spacers. Remember that the stop screw only sets the end position; it is not a mid-stroke lock.
Because this is a double-acting cylinder, the piston will drift if air pressure is lost or the valve is centered—use an external rod lock or pilot-operated check valve for held loads. For mounting, you can utilize LB foot, FA flange, or TC trunnion brackets, along with CA, U, R, or CM back covers, but the SDB pivot block is not available on this adjustable variant. Position sensing is fully enabled via the built-in magnet for CMSG, DMSG, or EMSG switches.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MIJ Adjustable Cylinder MIJ16X50-30S FAQ
The theoretical maximum force is 20.5 kgf at 1.0 MPa.
An external stop screw shortens the extend stroke by up to 30mm on-site (usable range 20-50mm), while the retract stroke remains full length. The -S suffix indicates a built-in piston magnet for CMSG, DMSG, and EMSG sensors; the stainless steel build provides mild corrosion resistance.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac MIJ Adjustable Cylinder MIJ16X50-30S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.