Airtac MIJ Adjustable Cylinder MIJ16X60-30
The AirTAC MIJ Adjustable Cylinder MIJ16X60-30 is a genuine double acting, double rod, adjustable stroke round-body mini air cylinder with a Ø16mm bore and 60mm stroke, M5×0.8 air ports and a stainless-steel barrel and rod for mildly corrosive environments. Its ISO 6432 mounting interface fits standard ISO 6432 mini-cylinder mounting interfaces.
- BoreØ16 mm
- Stroke60 mm
- Port sizeM5×0.8
- Acting typeDouble acting, double rod, adjustable stroke
- Rod threadM6×1.0
- CushionFixed TPU bumper pads
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MIJ Adjustable Cylinder MIJ16X60-30
Trimming the forward end by up to 30 mm on site, the AirTAC MIJ16X60-30 lets you tune the extend stroke from 30 to 60 mm without swapping hardware.
Built with an M5×0.8 port and a Ø6 mm piston rod, it uses the ISO 6432 mounting interface for straightforward bracket drops. The stainless barrel and rod resist mild washdown corrosion. This SKU lacks a magnet, so it cannot host CMSG/DMSG/EMSG sensors; fixed TPU bumpers decelerate the stroke ends.
Airtac MIJ Adjustable Cylinder MIJ16X60-30 Technical Specifications
| Model | Airtac MIJ Adjustable Cylinder MIJ16X60-30 |
|---|---|
| Series | MIJ ISO 6432 mini cylinder |
| Bore size | Ø16 mm |
| Stroke | 60 mm |
| Acting type | Double acting, double rod, adjustable stroke |
| Port size | M5×0.8 |
| Rod thread | M6×1.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Fixed TPU bumper pads |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G.
Theoretical Output Force (Ø16mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 86 N |
| 0.7 MPa | 121 N |
| Max (@1.0 MPa) | 18 kgf |
MIJ / MICJ are double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
Model Code: Airtac MIJ Adjustable Cylinder MIJ16X60-30
| MIJ | ISO 6432 round-body mini cylinder (adjustable-stroke). |
|---|---|
| 16 | Bore size in mm. |
| ×60 | Stroke length in mm. |
| -30 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (double rod, adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MIJ Adjustable Cylinder MIJ16X60-30 Is Used
Bin Diverter Setup
Fine-tune the actuator reach to deflect small packages into different sorting bins, taking up mechanical tolerances during rapid changeovers.
Is the Airtac MIJ Adjustable Cylinder MIJ16X60-30 the Right Cylinder?
The 30 mm external stop nut is ideal for taking up mechanical tolerances or staging feeds, letting one part number cover several forward stops. Retract remains a full 60 mm.
Because this is a non-magnet SKU, position sensing is unavailable. The stop screw sets the end position but is not a mid-stroke lock; the piston will drift on air loss, so fit an external pilot check valve for held loads. Mount via LB, FA, or TC (SDB is unavailable here).
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MIJ Adjustable Cylinder MIJ16X60-30 FAQ
At 0.5 MPa it pushes 100.5 N and pulls 86.4 N. At 0.7 MPa it pushes 140.7 N and pulls 120.9 N. The theoretical max force is 20.5 kgf at 1.0 MPa, and the air port is M5×0.8.
An external stop screw shortens the extend stroke by up to 30 mm on site, while retract remains the full 60 mm. The screw only sets the end position; it is not a mid-stroke lock, and the piston will drift on air loss. This SKU has no magnet, so sensors cannot be fitted.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac MIJ Adjustable Cylinder MIJ16X60-30
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.