Airtac MIJ Adjustable Cylinder MIJ16X60-40
The AirTAC MIJ Adjustable Cylinder MIJ16X60-40 is a genuine double acting, double rod, adjustable stroke round-body mini air cylinder with a Ø16mm bore and 60mm stroke, M5×0.8 air ports and a stainless-steel barrel and rod for mildly corrosive environments. Its ISO 6432 mounting interface fits standard ISO 6432 mini-cylinder mounting interfaces.
- BoreØ16 mm
- Stroke60 mm
- Port sizeM5×0.8
- Acting typeDouble acting, double rod, adjustable stroke
- Rod threadM6×1.0
- CushionFixed TPU bumper pads
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MIJ Adjustable Cylinder MIJ16X60-40
Dial in your forward end position on-site with the AirTAC MIJ16X60-40, a double-acting round-body mini cylinder featuring a 40mm adjustable extend window. An external stop screw lets you shorten the forward stroke from its 60mm nominal length down to 20mm, absorbing setup tolerances without swapping hardware. Retract remains at the full stroke length.
Built with a stainless-steel barrel and piston rod for mild washdown resistance, this Ø16 bore unit pushes 100.5 N at 0.5 MPa. It uses the ISO 6432 mounting interface, accepts an M5×0.8 air port, and relies on fixed TPU bumper pads to decelerate the stroke ends. Because this SKU lacks the -S magnet, it cannot accept CMSG, DMSG, or EMSG sensors.
Airtac MIJ Adjustable Cylinder MIJ16X60-40 Technical Specifications
| Model | Airtac MIJ Adjustable Cylinder MIJ16X60-40 |
|---|---|
| Series | MIJ ISO 6432 mini cylinder |
| Bore size | Ø16 mm |
| Stroke | 60 mm |
| Acting type | Double acting, double rod, adjustable stroke |
| Port size | M5×0.8 |
| Rod thread | M6×1.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Fixed TPU bumper pads |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G.
Theoretical Output Force (Ø16mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 86 N |
| 0.7 MPa | 121 N |
| Max (@1.0 MPa) | 18 kgf |
MIJ / MICJ are double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
Model Code: Airtac MIJ Adjustable Cylinder MIJ16X60-40
| MIJ | ISO 6432 round-body mini cylinder (adjustable-stroke). |
|---|---|
| 16 | Bore size in mm. |
| ×60 | Stroke length in mm. |
| -40 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (double rod, adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MIJ Adjustable Cylinder MIJ16X60-40 Is Used
Gauge Positioning
Set the exact extension between 20mm and 60mm to trigger gauges, taking up mechanical tolerances with the stop screw instead of machining new spacers.
Light Pressing
Dial in a precise 40mm extend trim for seating small bearings or pins, relying on the fixed TPU bumpers to soften the final impact.
Is the Airtac MIJ Adjustable Cylinder MIJ16X60-40 the Right Cylinder?
When sizing this 16mm bore, stepping down to an MIJ12 drops the 0.5 MPa push force to 56.5 N, while moving up to an MIJ20 raises it to 157.0 N. The 40mm external adjuster is ideal for changeover jobs where you need one part number to cover several intermediate stops. Mount using LB foot, FA flange, or TC trunnion brackets (the SDB pivot block is not available on this adjustable variant). Keep in mind the stop screw sets the end position but does not lock the rod; for holding a load on air loss, install an external pilot check valve or rod lock.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MIJ Adjustable Cylinder MIJ16X60-40 FAQ
The theoretical maximum force is 20.5 kgf at 1.0 MPa, and the air port is M5×0.8.
An external stop screw shortens the extend stroke by up to 40mm on-site, giving a usable forward range of 20-60mm. The retract stroke remains full. This SKU has no magnet, so it cannot take position sensors; the -S variant is required for CMSG/DMSG/EMSG switches.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac MIJ Adjustable Cylinder MIJ16X60-40
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.