Airtac MIJ Adjustable Cylinder MIJ16X70-10S
The AirTAC MIJ Adjustable Cylinder MIJ16X70-10S is a genuine double acting, double rod, adjustable stroke round-body mini air cylinder with a Ø16mm bore and 70mm stroke, M5×0.8 air ports and a stainless-steel barrel and rod for mildly corrosive environments. Its ISO 6432 mounting interface fits standard ISO 6432 mini-cylinder mounting interfaces.
- BoreØ16 mm
- Stroke70 mm
- Port sizeM5×0.8
- Acting typeDouble acting, double rod, adjustable stroke
- Rod threadM6×1.0
- CushionFixed TPU bumper pads
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MIJ Adjustable Cylinder MIJ16X70-10S
Dial in a precise forward end position on-site with the AirTAC MIJ16X70-10S, a round-body stainless steel mini cylinder featuring a 10mm external stop-screw adjustment window.
The riveted stainless barrel and Ø6 mm piston rod naturally resist mild corrosion and washdown environments. Because this is an -S variant, the built-in piston magnet supports CMSG, DMSG, and EMSG position switches. It conforms to the ISO 6432 mounting interface for standard mini brackets, uses an M5×0.8 port, and relies on fixed TPU bumper pads to decelerate the stroke end.
Airtac MIJ Adjustable Cylinder MIJ16X70-10S Technical Specifications
| Model | Airtac MIJ Adjustable Cylinder MIJ16X70-10S |
|---|---|
| Series | MIJ ISO 6432 mini cylinder |
| Bore size | Ø16 mm |
| Stroke | 70 mm |
| Acting type | Double acting, double rod, adjustable stroke |
| Port size | M5×0.8 |
| Rod thread | M6×1.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Fixed TPU bumper pads |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G.
Theoretical Output Force (Ø16mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 86 N |
| 0.7 MPa | 121 N |
| Max (@1.0 MPa) | 18 kgf |
MIJ / MICJ are double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
Model Code: Airtac MIJ Adjustable Cylinder MIJ16X70-10S
| MIJ | ISO 6432 round-body mini cylinder (adjustable-stroke). |
|---|---|
| 16 | Bore size in mm. |
| ×70 | Stroke length in mm. |
| -10 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (double rod, adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MIJ Adjustable Cylinder MIJ16X70-10S Is Used
Transfer Diverter Arms
Fine-tune the forward reach of a diverter gate on a packaging line, leveraging the 5.1kg vertical lift capacity to redirect lightweight cartons accurately.
Is the Airtac MIJ Adjustable Cylinder MIJ16X70-10S the Right Cylinder?
The 10 mm extend adjuster is ideal for taking up mechanical tolerances during setup, letting one part number cover several slightly different forward stops without swapping hardware.
Mount using LB foot, FA flange, or TC trunnion brackets (SDB pivot-block is not available on this adjustable type). Remember the stop screw only trims the extend end and does not lock the piston mid-stroke; the cylinder will drift on air loss, so fit an external rod lock or pilot check valve for held loads.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MIJ Adjustable Cylinder MIJ16X70-10S FAQ
This 16 mm bore cylinder uses an M5×0.8 port. At 0.5 MPa it pushes 100.5 N and pulls 86.4 N. At 0.7 MPa it pushes 140.7 N and pulls 120.9 N. The theoretical maximum force is 20.5 kgf at 1.0 MPa.
An external stop screw shortens the extend stroke by up to 10 mm on-site (retract remains full). The -S suffix means a piston magnet is built-in for CMSG/DMSG/EMSG sensors. The cylinder uses fixed TPU bumpers, not an adjustable air cushion.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac MIJ Adjustable Cylinder MIJ16X70-10S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.