Airtac MIJ Adjustable Cylinder MIJ16X80-10S
The AirTAC MIJ Adjustable Cylinder MIJ16X80-10S is a genuine double acting, double rod, adjustable stroke round-body mini air cylinder with a Ø16mm bore and 80mm stroke, M5×0.8 air ports and a stainless-steel barrel and rod for mildly corrosive environments. Its ISO 6432 mounting interface fits standard ISO 6432 mini-cylinder mounting interfaces.
- BoreØ16 mm
- Stroke80 mm
- Port sizeM5×0.8
- Acting typeDouble acting, double rod, adjustable stroke
- Rod threadM6×1.0
- CushionFixed TPU bumper pads
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MIJ Adjustable Cylinder MIJ16X80-10S
Dial in your forward end position on the fly with the AirTAC MIJ16X80-10S, a round-body stainless steel mini cylinder that lets an external stop screw shorten the extend stroke by up to 10 mm without swapping parts.
Built with a riveted stainless barrel and rod for mild washdown resistance, it drops directly into standard ISO 6432 mini-cylinder brackets. The -S suffix equips the piston with a magnet for CMSG, DMSG, or EMSG sensors, while fixed TPU bumper pads absorb end-of-stroke impacts.
Airtac MIJ Adjustable Cylinder MIJ16X80-10S Technical Specifications
| Model | Airtac MIJ Adjustable Cylinder MIJ16X80-10S |
|---|---|
| Series | MIJ ISO 6432 mini cylinder |
| Bore size | Ø16 mm |
| Stroke | 80 mm |
| Acting type | Double acting, double rod, adjustable stroke |
| Port size | M5×0.8 |
| Rod thread | M6×1.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Fixed TPU bumper pads |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G.
Theoretical Output Force (Ø16mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 86 N |
| 0.7 MPa | 121 N |
| Max (@1.0 MPa) | 18 kgf |
MIJ / MICJ are double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
Model Code: Airtac MIJ Adjustable Cylinder MIJ16X80-10S
| MIJ | ISO 6432 round-body mini cylinder (adjustable-stroke). |
|---|---|
| 16 | Bore size in mm. |
| ×80 | Stroke length in mm. |
| -10 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (double rod, adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MIJ Adjustable Cylinder MIJ16X80-10S Is Used
Staged Parts Feed
Adjust the forward stop to push a 5.1 kg component into a fixture, allowing quick changeover for different part heights.
Is the Airtac MIJ Adjustable Cylinder MIJ16X80-10S the Right Cylinder?
The 10 mm adjustment window is perfect for taking up mechanical tolerances during setup. You can mount via LB foot, FA flange, or TC trunnion, but note the SDB pivot block is not offered on this adjustable variant.
Remember the stop screw only trims the extend end and will not lock the piston mid-stroke. If your application must hold a load on air loss, add an external rod lock or pilot check valve, as this cylinder will drift.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MIJ Adjustable Cylinder MIJ16X80-10S FAQ
At 0.5 MPa it pushes 100.5 N and pulls 86.4 N. At 0.7 MPa it pushes 140.7 N and pulls 120.9 N, with a theoretical max of 20.5 kgf at 1.0 MPa. The air port is M5×0.8 and the male rod thread is M6x1.0.
An external screw shortens the extend stroke by up to 10 mm on site, while retract remains full. The -S suffix means a built-in magnet is present for CMSG/DMSG/EMSG sensors. The stainless build resists mild corrosion.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac MIJ Adjustable Cylinder MIJ16X80-10S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.