Airtac MIJ Adjustable Cylinder MIJ16X80-30S
The AirTAC MIJ Adjustable Cylinder MIJ16X80-30S is a genuine double acting, double rod, adjustable stroke round-body mini air cylinder with a Ø16mm bore and 80mm stroke, M5×0.8 air ports and a stainless-steel barrel and rod for mildly corrosive environments. Its ISO 6432 mounting interface fits standard ISO 6432 mini-cylinder mounting interfaces.
- BoreØ16 mm
- Stroke80 mm
- Port sizeM5×0.8
- Acting typeDouble acting, double rod, adjustable stroke
- Rod threadM6×1.0
- CushionFixed TPU bumper pads
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MIJ Adjustable Cylinder MIJ16X80-30S
Dial in your forward end position on-site with the AirTAC MIJ16X80-30S, a double-acting round-body mini cylinder featuring a 30mm adjustable extend window. An external stop screw lets you trim the forward stroke anywhere from 50mm to the 80mm maximum without swapping parts, while retract remains full. The stainless-steel barrel and riveted construction shrug off mild washdown environments.
The -S suffix equips the piston with a magnet for CMSG, DMSG or EMSG position sensing.
Airtac MIJ Adjustable Cylinder MIJ16X80-30S Technical Specifications
| Model | Airtac MIJ Adjustable Cylinder MIJ16X80-30S |
|---|---|
| Series | MIJ ISO 6432 mini cylinder |
| Bore size | Ø16 mm |
| Stroke | 80 mm |
| Acting type | Double acting, double rod, adjustable stroke |
| Port size | M5×0.8 |
| Rod thread | M6×1.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Fixed TPU bumper pads |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G.
Theoretical Output Force (Ø16mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 86 N |
| 0.7 MPa | 121 N |
| Max (@1.0 MPa) | 18 kgf |
MIJ / MICJ are double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
Model Code: Airtac MIJ Adjustable Cylinder MIJ16X80-30S
| MIJ | ISO 6432 round-body mini cylinder (adjustable-stroke). |
|---|---|
| 16 | Bore size in mm. |
| ×80 | Stroke length in mm. |
| -30 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (double rod, adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MIJ Adjustable Cylinder MIJ16X80-30S Is Used
Tolerance Take-Up Press
Fine-tune the forward end position to absorb minor part variations during light-duty pressing tasks, preventing damage while delivering consistent contact.
Is the Airtac MIJ Adjustable Cylinder MIJ16X80-30S the Right Cylinder?
For lighter jobs, the Ø12 MIJ bore drops push force to 56.5N, whereas stepping up to the Ø20 MIJ increases it to 157.0N at 0.5MPa. The 30mm stop screw on this model is ideal for taking up mechanical tolerances during setup or covering multiple feed distances with one part number. Remember the stop screw sets the end position but does not lock the rod mid-stroke; the piston will drift on air loss, so fit an external pilot check valve if you need to hold a suspended load.
Mount using LB foot brackets, FA flanges or TC trunnions, as the SDB pivot block is not available on this adjustable variant. You can select back covers CA, U, R or CM for routing flexibility. Position sensing works seamlessly with CMSG, DMSG and EMSG switches because the -S magnet is factory-installed.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MIJ Adjustable Cylinder MIJ16X80-30S FAQ
At 0.5MPa this cylinder pushes 100.5N and pulls 86.4N. At 0.7MPa it pushes 140.7N and pulls 120.9N. The theoretical maximum force is 20.5kgf at 1.0MPa, and the air port is M5×0.8.
An external stop screw shortens the extend stroke by up to 30mm on-site, letting you set the exact forward end position without changing the cylinder; the retract stroke remains full. The -S suffix means a piston magnet is built-in for CMSG, DMSG or EMSG sensors.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac MIJ Adjustable Cylinder MIJ16X80-30S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.