Airtac MIJ Adjustable Cylinder MIJ16X80-75
The AirTAC MIJ Adjustable Cylinder MIJ16X80-75 is a genuine double acting, double rod, adjustable stroke round-body mini air cylinder with a Ø16mm bore and 80mm stroke, M5×0.8 air ports and a stainless-steel barrel and rod for mildly corrosive environments. Its ISO 6432 mounting interface fits standard ISO 6432 mini-cylinder mounting interfaces.
- BoreØ16 mm
- Stroke80 mm
- Port sizeM5×0.8
- Acting typeDouble acting, double rod, adjustable stroke
- Rod threadM6×1.0
- CushionFixed TPU bumper pads
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MIJ Adjustable Cylinder MIJ16X80-75
Dial in a precise forward end position on-site with the AirTAC MIJ16X80-75, a double-acting round-body mini cylinder featuring a 75 mm external adjustment window. An integrated stop screw shortens the extend stroke from its 80 mm nominal length down to 5 mm, allowing one unit to cover multiple stop distances without hardware swaps. The retract stroke remains full length. Built with a stainless-steel barrel and piston rod, it withstands mild washdowns and corrosive environments.
It uses an M5×0.8 port, a Ø6 mm rod, and fixed TPU bumper pads to decelerate the stroke end. Note this SKU lacks a magnet, so it cannot host CMSG/DMSG/EMSG sensors; choose the -S variant for position detection.
Airtac MIJ Adjustable Cylinder MIJ16X80-75 Technical Specifications
| Model | Airtac MIJ Adjustable Cylinder MIJ16X80-75 |
|---|---|
| Series | MIJ ISO 6432 mini cylinder |
| Bore size | Ø16 mm |
| Stroke | 80 mm |
| Acting type | Double acting, double rod, adjustable stroke |
| Port size | M5×0.8 |
| Rod thread | M6×1.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Fixed TPU bumper pads |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G.
Theoretical Output Force (Ø16mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 86 N |
| 0.7 MPa | 121 N |
| Max (@1.0 MPa) | 18 kgf |
MIJ / MICJ are double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
Model Code: Airtac MIJ Adjustable Cylinder MIJ16X80-75
| MIJ | ISO 6432 round-body mini cylinder (adjustable-stroke). |
|---|---|
| 16 | Bore size in mm. |
| ×80 | Stroke length in mm. |
| -75 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (double rod, adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MIJ Adjustable Cylinder MIJ16X80-75 Is Used
Adjustable Stop Gauging
Set varying material push depths on a single fixture. The 75 mm window lets operators dial in the exact extend stop for different part lengths without swapping cylinders.
Staged Part Diversion
Sort lightweight packages on a belt by fine-tuning the diverter arm stroke. The 60 N safe working capacity easily pushes small items without overshooting.
Tolerance Take-Up Clamping
Compensate for minor workpiece variations during clamping. Adjust the forward end position on-site to ensure consistent 100.5 N contact force @0.5 MPa.
Is the Airtac MIJ Adjustable Cylinder MIJ16X80-75 the Right Cylinder?
The 75 mm adjuster is ideal for taking up mechanical tolerances during setup or staging feeds across changeover jobs. Remember the stop screw sets the end position but is not a mid-stroke lock; the piston will drift on air loss, so fit an external pilot check valve if you must hold a suspended load. Mount via LB foot, FA flange, or TC trunnion (SDB pivot-block is unavailable here), and use standard ISO 6432 mini brackets.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MIJ Adjustable Cylinder MIJ16X80-75 FAQ
The theoretical maximum force is 20.5 kgf at 1.0 MPa. This 16 mm bore unit features an M5×0.8 air port and a Ø6 mm piston rod.
An external stop screw shortens the extend stroke by up to 75 mm (usable range 5-80 mm); the retract stroke remains full. The screw only sets the forward end position—it is not a mid-stroke lock. The cylinder drifts on air loss, so use a pilot check valve to hold loads. This non-S SKU has no magnet for sensors.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac MIJ Adjustable Cylinder MIJ16X80-75
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.