Airtac MIJ Adjustable Cylinder MIJ25X10-10S
The AirTAC MIJ Adjustable Cylinder MIJ25X10-10S is a genuine double acting, double rod, adjustable stroke round-body mini air cylinder with a Ø25mm bore and 10mm stroke, 1/8" air ports and a stainless-steel barrel and rod for mildly corrosive environments. Its ISO 6432 mounting interface fits standard ISO 6432 mini-cylinder mounting interfaces.
- BoreØ25 mm
- Stroke10 mm
- Port size1/8"
- Acting typeDouble acting, double rod, adjustable stroke
- Rod threadM10×1.25
- CushionFixed TPU bumper pads
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MIJ Adjustable Cylinder MIJ25X10-10S
Dial in your forward end position on site with the MIJ25X10-10S. Its external stop screw shortens the extend stroke by up to 10 mm, so you can fine-tune the cylinder's reach without swapping parts or re-piping. The retract stroke remains full, and the stainless round barrel and rod shrug off mild corrosion and washdown splashes.
The built-in piston magnet enables CMSG, DMSG, or EMSG sensors for reliable position feedback. With a 1/8" port and M10x1.25 male rod thread, it integrates into standard mini-cylinder mounting brackets and clevises.
Airtac MIJ Adjustable Cylinder MIJ25X10-10S Technical Specifications
| Model | Airtac MIJ Adjustable Cylinder MIJ25X10-10S |
|---|---|
| Series | MIJ ISO 6432 mini cylinder |
| Bore size | Ø25 mm |
| Stroke | 10 mm |
| Acting type | Double acting, double rod, adjustable stroke |
| Port size | 1/8" |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Fixed TPU bumper pads |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G.
Theoretical Output Force (Ø25mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 206 N |
| 0.7 MPa | 289 N |
| Max (@1.0 MPa) | 42 kgf |
MIJ / MICJ are double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
Model Code: Airtac MIJ Adjustable Cylinder MIJ25X10-10S
| MIJ | ISO 6432 round-body mini cylinder (adjustable-stroke). |
|---|---|
| 25 | Bore size in mm. |
| ×10 | Stroke length in mm. |
| -10 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (double rod, adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MIJ Adjustable Cylinder MIJ25X10-10S Is Used
Fixture Stop Adjustment
Set the exact forward stop on a work-holding fixture by turning the external screw. The 10 mm adjustment window lets you fine-tune part location without machining shims or replacing the cylinder.
Staged Feed Positioning
Use the adjustable extend stroke to create a two-stage feed: a fast approach followed by a precise, shortened final push.
Changeover Quick-Change
When switching product sizes on a line, re-dial the stop screw instead of swapping cylinders. The MIJ25X10-10S covers a 10 mm range of end positions, reducing changeover downtime.
Is the Airtac MIJ Adjustable Cylinder MIJ25X10-10S the Right Cylinder?
Size this bore against your load: at 0.5 MPa it pushes 245.3 N and pulls 206.1 N. If you need less force, the MIJ20 bore pushes 157.0 N; if you need more headroom, the MIJ32 bore pushes 402.2 N at the same pressure. The 10 mm adjustable stroke is ideal for absorbing tolerance stack-up or setting a precise stop position during setup.
Remember, the stop screw sets the end position but does not lock the load. For holding a load in position on air loss, use an external rod lock or a pilot-operated check valve. The fixed TPU bumpers only soften the stroke end. Since this SKU includes the -S magnet, you can mount CMSG, DMSG, or EMSG sensors directly.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MIJ Adjustable Cylinder MIJ25X10-10S FAQ
At 0.5 MPa, push force is 245.3 N and pull force is 206.1 N. At 0.7 MPa, push is 343.4 N and pull is 288.5 N. The theoretical maximum force is 50 kgf at 1.0 MPa.
The external stop screw shortens the extend end position by up to 10 mm; retract is always full. It is not a mid-stroke lock. This -S version has a built-in magnet, so you can attach CMSG, DMSG, or EMSG sensors to detect piston position.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac MIJ Adjustable Cylinder MIJ25X10-10S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.