Airtac MIJ Adjustable Cylinder MIJ25X100-30
The AirTAC MIJ Adjustable Cylinder MIJ25X100-30 is a genuine double acting, double rod, adjustable stroke round-body mini air cylinder with a Ø25mm bore and 100mm stroke, 1/8" air ports and a stainless-steel barrel and rod for mildly corrosive environments. Its ISO 6432 mounting interface fits standard ISO 6432 mini-cylinder mounting interfaces.
- BoreØ25 mm
- Stroke100 mm
- Port size1/8"
- Acting typeDouble acting, double rod, adjustable stroke
- Rod threadM10×1.25
- CushionFixed TPU bumper pads
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MIJ Adjustable Cylinder MIJ25X100-30
Trimming the forward end position by up to 30 mm on site, the AirTAC MIJ25X100-30 lets you fine-tune a 100 mm extend stroke without swapping hardware. This double-acting, round-body mini cylinder features a stainless-steel barrel and piston rod to resist mild corrosion and washdown environments.
It uses the ISO 6432 mounting interface for standard mini brackets and relies on fixed TPU bumper pads to decelerate the stroke end.
Airtac MIJ Adjustable Cylinder MIJ25X100-30 Technical Specifications
| Model | Airtac MIJ Adjustable Cylinder MIJ25X100-30 |
|---|---|
| Series | MIJ ISO 6432 mini cylinder |
| Bore size | Ø25 mm |
| Stroke | 100 mm |
| Acting type | Double acting, double rod, adjustable stroke |
| Port size | 1/8" |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Fixed TPU bumper pads |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G.
Theoretical Output Force (Ø25mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 206 N |
| 0.7 MPa | 289 N |
| Max (@1.0 MPa) | 42 kgf |
MIJ / MICJ are double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
Model Code: Airtac MIJ Adjustable Cylinder MIJ25X100-30
| MIJ | ISO 6432 round-body mini cylinder (adjustable-stroke). |
|---|---|
| 25 | Bore size in mm. |
| ×100 | Stroke length in mm. |
| -30 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (double rod, adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MIJ Adjustable Cylinder MIJ25X100-30 Is Used
Precision Feeder Stops
Dial in the exact 70 to 100 mm extend position to index cardboard blanks without re-specifying the entire cylinder for every carton size changeover.
Washdown Pin Insertion
Leverage the stainless steel construction and 12.5 kg vertical lift capacity to press pins in damp environments, adjusting the end stop for different material thicknesses.
Is the Airtac MIJ Adjustable Cylinder MIJ25X100-30 the Right Cylinder?
The 30 mm adjustment window is ideal for taking up mechanical tolerances during setup or covering multiple stop positions with a single part number.
Because this SKU lacks the -S magnet, it cannot accept CMSG, DMSG, or EMSG sensors. You can use LB, FA, or TC mounts alongside CA, U, R, or CM back covers, but note that the SDB pivot block is not offered. The external screw sets the forward end position only; it is not a mid-stroke lock, and the piston will drift on air loss unless you add an external rod lock or pilot check valve.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MIJ Adjustable Cylinder MIJ25X100-30 FAQ
The theoretical maximum force is 50 kgf at 1.0 MPa, and the air port size is 1/8".
An external stop screw shortens the extend stroke by up to 30 mm on site, while retract remains full. The screw only sets the end position and is not a mid-stroke lock; the piston will drift on air loss. This non-S SKU also lacks a magnet for sensors.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac MIJ Adjustable Cylinder MIJ25X100-30
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.