Airtac MIJ Adjustable Cylinder MIJ25X150-10S
The AirTAC MIJ Adjustable Cylinder MIJ25X150-10S is a genuine double acting, double rod, adjustable stroke round-body mini air cylinder with a Ø25mm bore and 150mm stroke, 1/8" air ports and a stainless-steel barrel and rod for mildly corrosive environments. Its ISO 6432 mounting interface fits standard ISO 6432 mini-cylinder mounting interfaces.
- BoreØ25 mm
- Stroke150 mm
- Port size1/8"
- Acting typeDouble acting, double rod, adjustable stroke
- Rod threadM10×1.25
- CushionFixed TPU bumper pads
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MIJ Adjustable Cylinder MIJ25X150-10S
Dial in a precise forward end position on the fly with the AirTAC MIJ25X150-10S, a double-acting round-body mini cylinder built with a stainless-steel barrel and piston rod for mild washdown resistance. An external stop screw lets you shorten the extend stroke by up to 10 mm on site, giving a usable forward range of 140 to 150 mm without swapping parts. Retract remains a full 150 mm stroke, and the fixed TPU bumper pads decelerate the piston at the ends.
The 1/8" air port and M10x1.25 male rod thread match standard Ø25 mini-cylinder hardware, and the -S suffix means a built-in magnet is ready for CMSG, DMSG or EMSG sensors.
Airtac MIJ Adjustable Cylinder MIJ25X150-10S Technical Specifications
| Model | Airtac MIJ Adjustable Cylinder MIJ25X150-10S |
|---|---|
| Series | MIJ ISO 6432 mini cylinder |
| Bore size | Ø25 mm |
| Stroke | 150 mm |
| Acting type | Double acting, double rod, adjustable stroke |
| Port size | 1/8" |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Fixed TPU bumper pads |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G.
Theoretical Output Force (Ø25mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 206 N |
| 0.7 MPa | 289 N |
| Max (@1.0 MPa) | 42 kgf |
MIJ / MICJ are double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
Model Code: Airtac MIJ Adjustable Cylinder MIJ25X150-10S
| MIJ | ISO 6432 round-body mini cylinder (adjustable-stroke). |
|---|---|
| 25 | Bore size in mm. |
| ×150 | Stroke length in mm. |
| -10 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (double rod, adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MIJ Adjustable Cylinder MIJ25X150-10S Is Used
Staged Ejection Pusher
Uses the 245.3 N extend force to push cartons off a belt while the 10 mm stop screw dials in the exact ejection point for different box lengths.
Tolerance Take-up Stop
Acts as a hard stop for machined parts, trimming the forward end position by up to 10 mm to absorb fixture tolerances without reprogramming the PLC.
Vertical Lift Gate
Lifts a roughly 12.5 kg gate using the 0.5 MPa push force, with the built-in magnet enabling DMSG sensors to confirm the raised position.
Is the Airtac MIJ Adjustable Cylinder MIJ25X150-10S the Right Cylinder?
When sizing this 25 mm bore, stepping down to a MIJ20 unit drops the 0.5 MPa push force to 157.0 N, whereas stepping up to a MIJ32 raises it to 402.2 N. The 10 mm extend adjuster is ideal for taking up mechanical tolerances or staggering part ejection during changeovers. Remember the stop screw only sets the forward end position; it is not a mid-stroke lock, and the piston will drift on air loss, so fit an external rod lock or pilot check valve to hold a suspended load.
Mounting options include LB foot, FA flange and TC trunnion brackets, plus CA, U, R and CM back covers, but the SDB pivot block is not available on this adjustable variant. Position sensing is fully enabled here because the -S magnet is present, allowing direct fitment of CMSG, DMSG or EMSG switches.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MIJ Adjustable Cylinder MIJ25X150-10S FAQ
The theoretical maximum force is 50 kgf at 1.0 MPa. The air port is 1/8".
An external stop screw shortens the extend stroke by up to 10 mm on site, giving a usable forward range of 140 to 150 mm, while retract stays at the full 150 mm. The -S suffix indicates a built-in piston magnet for use with CMSG, DMSG or EMSG sensors.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac MIJ Adjustable Cylinder MIJ25X150-10S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.