Airtac MIJ Adjustable Cylinder MIJ25X175-10SFA
The AirTAC MIJ Adjustable Cylinder MIJ25X175-10SFA is a genuine double acting, double rod, adjustable stroke round-body mini air cylinder with a Ø25mm bore and 175mm stroke, 1/8" air ports and a stainless-steel barrel and rod for mildly corrosive environments. Its ISO 6432 mounting interface fits standard ISO 6432 mini-cylinder mounting interfaces.
- BoreØ25 mm
- Stroke175 mm
- Port size1/8"
- Acting typeDouble acting, double rod, adjustable stroke
- Rod threadM10×1.25
- CushionFixed TPU bumper pads
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MIJ Adjustable Cylinder MIJ25X175-10SFA
Dial in a precise forward end position on-site with the AirTAC MIJ25X175-10SFA, a double-acting round-body mini cylinder built with a stainless-steel barrel and rod for mild corrosion resistance. An external stop screw shortens the extend stroke by up to 10 mm, giving you a usable forward range of 165 to 175 mm without swapping parts. Retract remains a full 175 mm, and the Ø10 mm piston rod uses an M10x1.25 male thread.
The -S suffix denotes a built-in piston magnet for CMSG, DMSG, or EMSG position sensing, while fixed TPU bumper pads decelerate the stroke ends across a 30-800 mm/s speed range. Air connects via a 1/8" port.
Airtac MIJ Adjustable Cylinder MIJ25X175-10SFA Technical Specifications
| Model | Airtac MIJ Adjustable Cylinder MIJ25X175-10SFA |
|---|---|
| Series | MIJ ISO 6432 mini cylinder |
| Bore size | Ø25 mm |
| Stroke | 175 mm |
| Acting type | Double acting, double rod, adjustable stroke |
| Port size | 1/8" |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Fixed TPU bumper pads |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G.
Theoretical Output Force (Ø25mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 206 N |
| 0.7 MPa | 289 N |
| Max (@1.0 MPa) | 42 kgf |
MIJ / MICJ are double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
Model Code: Airtac MIJ Adjustable Cylinder MIJ25X175-10SFA
| MIJ | ISO 6432 round-body mini cylinder (adjustable-stroke). |
|---|---|
| 25 | Bore size in mm. |
| ×175 | Stroke length in mm. |
| -10 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (double rod, adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MIJ Adjustable Cylinder MIJ25X175-10SFA Is Used
Changeover Sorting Stop
Adjust the forward stop screw to handle different box heights during product changeovers, leveraging the 12.5 kg vertical lift capacity for light palletizing tasks.
Is the Airtac MIJ Adjustable Cylinder MIJ25X175-10SFA the Right Cylinder?
When sizing this 25 mm bore, stepping down to a 20 mm MIJ drops the 0.5 MPa push force to 157 N, whereas moving up to a 32 mm bore increases it to 402 N. The 10 mm external stop screw is ideal for taking up mechanical tolerances during setup or covering several intermediate stops with one assembly. The FA flange accessory is included for secure mounting, though the SDB pivot block is not offered on this adjustable variant.
Position holding requires external hardware, as the piston drifts on air loss and the stop screw only sets the end position rather than acting as a mid-stroke lock. For suspended loads, pair the cylinder with an external rod lock or a pilot-operated check valve.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MIJ Adjustable Cylinder MIJ25X175-10SFA FAQ
The theoretical maximum force is 50 kgf at 1.0 MPa. The air port size is 1/8".
The external stop screw shortens the extend stroke by up to 10 mm, allowing a usable forward range of 165 to 175 mm, while retract remains the full 175 mm. The -S suffix means a piston magnet is built-in for CMSG, DMSG, or EMSG sensors, and the stainless construction resists mild washdown environments.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac MIJ Adjustable Cylinder MIJ25X175-10SFA
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.