Airtac MIJ Adjustable Cylinder MIJ25X200-50
The AirTAC MIJ Adjustable Cylinder MIJ25X200-50 is a genuine double acting, double rod, adjustable stroke round-body mini air cylinder with a Ø25mm bore and 200mm stroke, 1/8" air ports and a stainless-steel barrel and rod for mildly corrosive environments. Its ISO 6432 mounting interface fits standard ISO 6432 mini-cylinder mounting interfaces.
- BoreØ25 mm
- Stroke200 mm
- Port size1/8"
- Acting typeDouble acting, double rod, adjustable stroke
- Rod threadM10×1.25
- CushionFixed TPU bumper pads
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MIJ Adjustable Cylinder MIJ25X200-50
Trimming the forward end by up to 50 mm via an external stop screw, this round-body stainless steel mini cylinder lets you dial in the exact extend position from 150 to 200 mm on site.
Built with a stainless barrel and rod for mild washdown resistance, it conforms to the ISO 6432 mounting interface for standard mini brackets. The 1/8" port and M10x1.25 male rod thread handle the pneumatic flow, while fixed TPU bumper pads decelerate the stroke end. This non-magnet SKU cannot host sensors; the -S variant is required for CMSG/DMSG/EMSG switches.
Airtac MIJ Adjustable Cylinder MIJ25X200-50 Technical Specifications
| Model | Airtac MIJ Adjustable Cylinder MIJ25X200-50 |
|---|---|
| Series | MIJ ISO 6432 mini cylinder |
| Bore size | Ø25 mm |
| Stroke | 200 mm |
| Acting type | Double acting, double rod, adjustable stroke |
| Port size | 1/8" |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Fixed TPU bumper pads |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G.
Theoretical Output Force (Ø25mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 206 N |
| 0.7 MPa | 289 N |
| Max (@1.0 MPa) | 42 kgf |
MIJ / MICJ are double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
Model Code: Airtac MIJ Adjustable Cylinder MIJ25X200-50
| MIJ | ISO 6432 round-body mini cylinder (adjustable-stroke). |
|---|---|
| 25 | Bore size in mm. |
| ×200 | Stroke length in mm. |
| -50 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (double rod, adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MIJ Adjustable Cylinder MIJ25X200-50 Is Used
Tolerance Take-Up Clamp
Dial the screw in 5 mm increments to compensate for varying part thicknesses, applying a precise clamping force before a machining operation.
Adjustable Pallet Stop
Fine-tune the forward end position to catch different pallet depths on a packing line, absorbing the impact with fixed TPU bumper pads.
Is the Airtac MIJ Adjustable Cylinder MIJ25X200-50 the Right Cylinder?
If your application requires less force, stepping down to the 20 mm bore drops the push to 157.0 N, whereas moving up to the 32 mm bore increases it to 402.2 N. The 50 mm adjustment window is ideal for taking up mechanical tolerances during setup, allowing one part number to cover several intermediate stops without swapping cylinders.
Mount using LB foot, FA flange, or TC trunnion brackets, noting the SDB pivot block is not offered on this adjustable type. The stop screw sets the forward end position but acts purely as an end stop, not a mid-stroke lock; the piston will drift on air loss, so fit an external rod lock or pilot check valve to hold a suspended load.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MIJ Adjustable Cylinder MIJ25X200-50 FAQ
This 25 mm bore cylinder uses a 1/8" port and an M10x1.25 rod thread. At 0.5 MPa it pushes with 245.3 N and pulls with 206.1 N. At 0.7 MPa the push is 343.4 N and pull is 288.5 N. The theoretical maximum force is 50 kgf at 1.0 MPa.
An external stop screw shortens the extend stroke by up to 50 mm on site, giving a usable forward range of 150 to 200 mm while retract remains full. The screw only sets the end position; it is not a mid-stroke lock, and the piston will drift on air loss. This non-magnet SKU cannot take sensors.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac MIJ Adjustable Cylinder MIJ25X200-50
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.