Airtac MIJ Adjustable Cylinder MIJ25X225-10
The AirTAC MIJ Adjustable Cylinder MIJ25X225-10 is a genuine double acting, double rod, adjustable stroke round-body mini air cylinder with a Ø25mm bore and 225mm stroke, 1/8" air ports and a stainless-steel barrel and rod for mildly corrosive environments. Its ISO 6432 mounting interface fits standard ISO 6432 mini-cylinder mounting interfaces.
- BoreØ25 mm
- Stroke225 mm
- Port size1/8"
- Acting typeDouble acting, double rod, adjustable stroke
- Rod threadM10×1.25
- CushionFixed TPU bumper pads
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MIJ Adjustable Cylinder MIJ25X225-10
Dialing in a precise forward end position on-site is effortless with the AirTAC MIJ25X225-10, a round-body stainless steel mini cylinder featuring a 10 mm external stop screw that shortens the extend stroke from its 225 mm nominal length down to 215 mm. The retract stroke remains full, and because you trim the forward end mechanically, one part number covers several slightly different stops without swapping hardware.
The bore uses a 1/8" port and an M10×1.25 male rod thread, conforming to the ISO 6432 mounting interface for easy bracket drops. Fixed TPU bumper pads decelerate the stroke ends, and because this specific SKU lacks the -S magnet, it cannot accept CMSG, DMSG, or EMSG sensors.
Airtac MIJ Adjustable Cylinder MIJ25X225-10 Technical Specifications
| Model | Airtac MIJ Adjustable Cylinder MIJ25X225-10 |
|---|---|
| Series | MIJ ISO 6432 mini cylinder |
| Bore size | Ø25 mm |
| Stroke | 225 mm |
| Acting type | Double acting, double rod, adjustable stroke |
| Port size | 1/8" |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Fixed TPU bumper pads |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G.
Theoretical Output Force (Ø25mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 206 N |
| 0.7 MPa | 289 N |
| Max (@1.0 MPa) | 42 kgf |
MIJ / MICJ are double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
Model Code: Airtac MIJ Adjustable Cylinder MIJ25X225-10
| MIJ | ISO 6432 round-body mini cylinder (adjustable-stroke). |
|---|---|
| 25 | Bore size in mm. |
| ×225 | Stroke length in mm. |
| -10 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (double rod, adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MIJ Adjustable Cylinder MIJ25X225-10 Is Used
Staged Part Ejection
Trimming the 225 mm extend stroke by up to 10 mm lets you synchronize a 12.5 kg parts push-off with a moving belt without re-engineering the fixture.
Tooling Clearance Setup
Use the adjustable forward end position to dial in exact tool clearance during changeovers, relying on the stainless build to resist coolant mist.
Is the Airtac MIJ Adjustable Cylinder MIJ25X225-10 the Right Cylinder?
The 10 mm extend adjustment window is ideal for taking up mechanical tolerances or fine-tuning a staged feed, but remember the stop screw only sets the end position—it is not a mid-stroke lock. If the application requires holding a load on air loss, you must add an external rod lock or pilot check valve, as the piston will drift.
Mounting options include LB foot, FA flange, and TC trunnion styles, along with CA, U, R, or CM back covers, but the SDB pivot block is not available on this adjustable-stroke variant. Operating speed ranges from 30-800 mm/s. If you need position sensing, select the -S magnet version instead, as this base SKU cannot host a reed or solid-state switch.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MIJ Adjustable Cylinder MIJ25X225-10 FAQ
The theoretical maximum force is 50 kgf at 1.0 MPa. The air port size is 1/8".
An external stop screw shortens the extend stroke by up to 10 mm, giving a usable forward range of 215-225 mm; retract remains full. The screw only sets the end position and is not a mid-stroke lock. This SKU has no magnet (-S), so it cannot accept position sensors.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac MIJ Adjustable Cylinder MIJ25X225-10
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.