Airtac MIJ Adjustable Cylinder MIJ25X25-10S
The AirTAC MIJ Adjustable Cylinder MIJ25X25-10S is a genuine double acting, double rod, adjustable stroke round-body mini air cylinder with a Ø25mm bore and 25mm stroke, 1/8" air ports and a stainless-steel barrel and rod for mildly corrosive environments. Its ISO 6432 mounting interface fits standard ISO 6432 mini-cylinder mounting interfaces.
- BoreØ25 mm
- Stroke25 mm
- Port size1/8"
- Acting typeDouble acting, double rod, adjustable stroke
- Rod threadM10×1.25
- CushionFixed TPU bumper pads
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MIJ Adjustable Cylinder MIJ25X25-10S
Dial in a precise forward end position on-site with the AirTAC MIJ25X25-10S, a round-body stainless mini cylinder built for double-acting service. An external stop screw lets you shorten the extend stroke by up to 10 mm, yielding a usable forward travel of 15 to 25 mm without changing the hardware. Because the retract stroke remains full, you get rapid reset cycles while trimming only the forward thrust target.
The riveted stainless barrel and rod shrug off mild washdown environments. Fitted with a 1/8" port and an M10x1.25 male rod thread, this ISO 6432 mounting-interface unit includes a piston magnet for position sensing.
Airtac MIJ Adjustable Cylinder MIJ25X25-10S Technical Specifications
| Model | Airtac MIJ Adjustable Cylinder MIJ25X25-10S |
|---|---|
| Series | MIJ ISO 6432 mini cylinder |
| Bore size | Ø25 mm |
| Stroke | 25 mm |
| Acting type | Double acting, double rod, adjustable stroke |
| Port size | 1/8" |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Fixed TPU bumper pads |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G.
Theoretical Output Force (Ø25mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 206 N |
| 0.7 MPa | 289 N |
| Max (@1.0 MPa) | 42 kgf |
MIJ / MICJ are double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
Model Code: Airtac MIJ Adjustable Cylinder MIJ25X25-10S
| MIJ | ISO 6432 round-body mini cylinder (adjustable-stroke). |
|---|---|
| 25 | Bore size in mm. |
| ×25 | Stroke length in mm. |
| -10 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (double rod, adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MIJ Adjustable Cylinder MIJ25X25-10S Is Used
Staged Part Escapement
Use the 10 mm extend adjustment to tune the pusher distance precisely, releasing one component at a time onto a moving belt without over-traveling.
Light Press Fit
Apply a safe 147 N working load to seat small bearings, relying on the external screw to prevent bottoming out and protect delicate assemblies.
Is the Airtac MIJ Adjustable Cylinder MIJ25X25-10S the Right Cylinder?
The 10 mm external stop screw is ideal for taking up mechanical tolerances during setup or staging feeds, letting one part number cover several intermediate stops. Remember the stop screw sets the end position but acts purely as a bumper; it is not a mid-stroke lock, so fit an external rod lock or pilot check valve if you must hold a load on air loss.
This SKU includes the -S magnet, enabling CMSG, DMSG or EMSG switches for end-of-stroke confirmation. You can mount it using LB foot, FA flange or TC trunnion brackets, plus CA, U, R or CM back covers. Note the SDB pivot-block is not offered on adjustable-stroke variants. Fixed TPU bumper pads decelerate the stroke ends across the 30-800 mm/s speed range.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MIJ Adjustable Cylinder MIJ25X25-10S FAQ
The theoretical maximum force is 50 kgf at 1.0 MPa. The air port is 1/8".
An external stop screw shortens the extend stroke by up to 10 mm on-site, setting the exact forward position without swapping cylinders; the retract stroke remains full. The -S suffix means a piston magnet is built-in for CMSG, DMSG or EMSG sensors. Fixed TPU bumpers decelerate the stroke ends.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac MIJ Adjustable Cylinder MIJ25X25-10S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.