Airtac MIJ Adjustable Cylinder MIJ25X30-10
The AirTAC MIJ Adjustable Cylinder MIJ25X30-10 is a genuine double acting, double rod, adjustable stroke round-body mini air cylinder with a Ø25mm bore and 30mm stroke, 1/8" air ports and a stainless-steel barrel and rod for mildly corrosive environments. Its ISO 6432 mounting interface fits standard ISO 6432 mini-cylinder mounting interfaces.
- BoreØ25 mm
- Stroke30 mm
- Port size1/8"
- Acting typeDouble acting, double rod, adjustable stroke
- Rod threadM10×1.25
- CushionFixed TPU bumper pads
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MIJ Adjustable Cylinder MIJ25X30-10
Trimming the forward end by up to 10 mm on site, this round-body stainless steel mini cylinder lets you fine-tune the extend position from 20 to 30 mm without changing the hardware. The external stop screw sets the forward limit while retract remains a full 30 mm stroke.
Built with a stainless barrel and rod, the riveted construction handles mild corrosion and washdown environments. It uses the ISO 6432 mounting interface for standard mini brackets and features a 1/8" port with an M10x1.25 male rod thread. Because this SKU lacks the -S magnet, it cannot accept CMSG, DMSG, or EMSG sensors.
Airtac MIJ Adjustable Cylinder MIJ25X30-10 Technical Specifications
| Model | Airtac MIJ Adjustable Cylinder MIJ25X30-10 |
|---|---|
| Series | MIJ ISO 6432 mini cylinder |
| Bore size | Ø25 mm |
| Stroke | 30 mm |
| Acting type | Double acting, double rod, adjustable stroke |
| Port size | 1/8" |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Fixed TPU bumper pads |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G.
Theoretical Output Force (Ø25mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 206 N |
| 0.7 MPa | 289 N |
| Max (@1.0 MPa) | 42 kgf |
MIJ / MICJ are double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
Model Code: Airtac MIJ Adjustable Cylinder MIJ25X30-10
| MIJ | ISO 6432 round-body mini cylinder (adjustable-stroke). |
|---|---|
| 25 | Bore size in mm. |
| ×30 | Stroke length in mm. |
| -10 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (double rod, adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MIJ Adjustable Cylinder MIJ25X30-10 Is Used
Diverter Gate Adjustment
Fine-tune the extend position by up to 10 mm to perfectly align a diverter gate on a packaging line, accommodating belt wear or product size changes without swapping actuators.
Carton Stop Positioning
Securely halt corrugated cartons on a roller conveyor by adjusting the forward stop screw on site, ensuring positive stops without needing custom spacers or shims.
Is the Airtac MIJ Adjustable Cylinder MIJ25X30-10 the Right Cylinder?
For heavier demands, stepping up to the MIJ32 yields 402.2 N. The 10 mm external stop screw is ideal for taking up mechanical tolerances during setup or staging feeds, allowing one part number to cover several slightly different forward positions.
Mounting options include LB foot, FA flange, and TC trunnion, but the SDB pivot block is not available on this adjustable variant. Remember that the stop screw only sets the end position; it is not a mid-stroke lock. The piston will drift on air loss, so add an external rod lock or pilot check valve if you need to hold a load vertically. To add position sensing, you must switch to the -S magnet version of this cylinder.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MIJ Adjustable Cylinder MIJ25X30-10 FAQ
This double-acting cylinder uses a 1/8" port and an M10x1.25 male rod thread. The theoretical maximum force is 50 kgf at 1.0 MPa.
An external stop screw shortens the extend stroke by up to 10 mm, letting you set the forward end position between 20 and 30 mm; the retract stroke remains fixed at 30 mm. The stop screw is not a mid-stroke lock, and the cylinder will drift on air loss, so use an external rod lock for holding loads. This non-magnet SKU cannot take sensors.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac MIJ Adjustable Cylinder MIJ25X30-10
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.