Airtac MIJ Adjustable Cylinder MIJ25X75-40S
The AirTAC MIJ Adjustable Cylinder MIJ25X75-40S is a genuine double acting, double rod, adjustable stroke round-body mini air cylinder with a Ø25mm bore and 75mm stroke, 1/8" air ports and a stainless-steel barrel and rod for mildly corrosive environments. Its ISO 6432 mounting interface fits standard ISO 6432 mini-cylinder mounting interfaces.
- BoreØ25 mm
- Stroke75 mm
- Port size1/8"
- Acting typeDouble acting, double rod, adjustable stroke
- Rod threadM10×1.25
- CushionFixed TPU bumper pads
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MIJ Adjustable Cylinder MIJ25X75-40S
Dial in a precise forward end position on-site with the AirTAC MIJ25X75-40S, a round-body stainless steel mini cylinder featuring a 40 mm extend-stroke adjustment window. An external stop screw trims the forward travel from its 75 mm nominal maximum down to 35 mm, letting you cover multiple stop distances with a single part number while retract remains full. The built-in piston magnet (-S) directly supports CMSG, DMSG, and EMSG position sensing.
The stainless barrel and rod resist mild corrosion and washdown, and the 1/8" port feeds a 10 mm rod with an M10x1.25 male thread. It conforms to the ISO 6432 mounting interface for standard mini brackets.
Airtac MIJ Adjustable Cylinder MIJ25X75-40S Technical Specifications
| Model | Airtac MIJ Adjustable Cylinder MIJ25X75-40S |
|---|---|
| Series | MIJ ISO 6432 mini cylinder |
| Bore size | Ø25 mm |
| Stroke | 75 mm |
| Acting type | Double acting, double rod, adjustable stroke |
| Port size | 1/8" |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Fixed TPU bumper pads |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G.
Theoretical Output Force (Ø25mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 206 N |
| 0.7 MPa | 289 N |
| Max (@1.0 MPa) | 42 kgf |
MIJ / MICJ are double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
Model Code: Airtac MIJ Adjustable Cylinder MIJ25X75-40S
| MIJ | ISO 6432 round-body mini cylinder (adjustable-stroke). |
|---|---|
| 25 | Bore size in mm. |
| ×75 | Stroke length in mm. |
| -40 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (double rod, adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MIJ Adjustable Cylinder MIJ25X75-40S Is Used
Adjustable Diverter Gates
Fine-tune the 75 mm extend stroke by up to 40 mm to set exact contact points on sorting conveyors, accommodating different package sizes without swapping hardware.
Multi-Height Pin Lifts
Leverage the 12.5 kg vertical lift capacity to raise workpieces, using the stop screw to dial in multiple staged heights for machining or inspection stations.
Is the Airtac MIJ Adjustable Cylinder MIJ25X75-40S the Right Cylinder?
The 40 mm adjustment window is ideal for absorbing mechanical tolerances or staging feeds during changeover. Remember that the stop screw only sets the end position; it is not a mid-stroke lock, so fit an external rod lock or pilot check valve if you must hold a load against air loss.
Mounting options include LB foot, FA flange, and TC trunnion, plus CA, U, R, or CM back covers, but the SDB pivot block is not offered on this adjustable variant. Fixed TPU bumper pads decelerate the stroke ends across the 30-800 mm/s speed range, keeping operation smooth without the complexity of an adjustable air cushion.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MIJ Adjustable Cylinder MIJ25X75-40S FAQ
It uses a 1/8" air port, a 10 mm piston rod, and an M10x1.25 male rod thread.
An external stop screw shortens the extend stroke by up to 40 mm on-site (usable extend 35-75 mm) without affecting the full retract stroke. The -S suffix indicates a built-in piston magnet for CMSG, DMSG, or EMSG sensors, and the stainless build resists mild corrosion.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac MIJ Adjustable Cylinder MIJ25X75-40S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.