Airtac MIJ Adjustable Cylinder MIJ25X80-10
The AirTAC MIJ Adjustable Cylinder MIJ25X80-10 is a genuine double acting, double rod, adjustable stroke round-body mini air cylinder with a Ø25mm bore and 80mm stroke, 1/8" air ports and a stainless-steel barrel and rod for mildly corrosive environments. Its ISO 6432 mounting interface fits standard ISO 6432 mini-cylinder mounting interfaces.
- BoreØ25 mm
- Stroke80 mm
- Port size1/8"
- Acting typeDouble acting, double rod, adjustable stroke
- Rod threadM10×1.25
- CushionFixed TPU bumper pads
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MIJ Adjustable Cylinder MIJ25X80-10
Dial in your forward end position on the fly with the AirTAC MIJ25X80-10, a double-acting round-body mini cylinder built with a stainless-steel barrel and rod for mild washdown resistance. An external stop screw lets you shorten the extend stroke by up to 10 mm on site, covering an effective forward travel of 70 to 80 mm so you can absorb setup tolerances from a single SKU. Retract travel remains fixed at the full 80 mm.
The Ø25 bore conforms to the ISO 6432 mounting interface for easy bracket drops, uses a 1/8" port, and relies on fixed TPU bumper pads to decelerate the stroke end. Because this SKU lacks the -S magnet, it cannot host CMSG, DMSG, or EMSG sensors.
Airtac MIJ Adjustable Cylinder MIJ25X80-10 Technical Specifications
| Model | Airtac MIJ Adjustable Cylinder MIJ25X80-10 |
|---|---|
| Series | MIJ ISO 6432 mini cylinder |
| Bore size | Ø25 mm |
| Stroke | 80 mm |
| Acting type | Double acting, double rod, adjustable stroke |
| Port size | 1/8" |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Fixed TPU bumper pads |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G.
Theoretical Output Force (Ø25mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 206 N |
| 0.7 MPa | 289 N |
| Max (@1.0 MPa) | 42 kgf |
MIJ / MICJ are double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
Model Code: Airtac MIJ Adjustable Cylinder MIJ25X80-10
| MIJ | ISO 6432 round-body mini cylinder (adjustable-stroke). |
|---|---|
| 25 | Bore size in mm. |
| ×80 | Stroke length in mm. |
| -10 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (double rod, adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MIJ Adjustable Cylinder MIJ25X80-10 Is Used
Press Fit Tuning
Use the 10 mm extend adjustment to fine-tune a 12.5 kg press fit operation, hitting exact insert depths without swapping cylinders.
Staged Diverting
Dial the forward stop in from 80 mm to 70 mm to alter a diverting stroke on the fly, accommodating different carton widths on the line.
Is the Airtac MIJ Adjustable Cylinder MIJ25X80-10 the Right Cylinder?
The 10 mm external stop screw is ideal for taking up mechanical slack or tuning a staged feed without machining new hard stops. Mount via LB foot, FA flange, or TC trunnion, but note the SDB pivot block is not offered on this adjustable variant.
The stop screw sets the forward end position but acts purely as an end stop, not a mid-stroke lock. If your application must hold a load vertically during air loss, add an external rod lock or pilot check valve, as the piston will drift and the TPU bumpers only soften the end impact.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MIJ Adjustable Cylinder MIJ25X80-10 FAQ
This double-acting cylinder uses a 1/8" port and a Ø10 mm piston rod with an M10x1.25 male thread.
An external stop screw shortens the extend stroke by up to 10 mm on site, while retract remains full. This SKU has no magnet, so it cannot accept CMSG, DMSG, or EMSG sensors; you would need the -S variant for position sensing.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac MIJ Adjustable Cylinder MIJ25X80-10
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.