Airtac MIJ Adjustable Cylinder MIJ25X80-30
The AirTAC MIJ Adjustable Cylinder MIJ25X80-30 is a genuine double acting, double rod, adjustable stroke round-body mini air cylinder with a Ø25mm bore and 80mm stroke, 1/8" air ports and a stainless-steel barrel and rod for mildly corrosive environments. Its ISO 6432 mounting interface fits standard ISO 6432 mini-cylinder mounting interfaces.
- BoreØ25 mm
- Stroke80 mm
- Port size1/8"
- Acting typeDouble acting, double rod, adjustable stroke
- Rod threadM10×1.25
- CushionFixed TPU bumper pads
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MIJ Adjustable Cylinder MIJ25X80-30
Dial in your forward end position on site with the AirTAC MIJ25X80-30, a double-acting round-body mini cylinder featuring a 30 mm extend-stroke adjustment window. An external stop screw lets you shorten the forward travel from its 80 mm nominal length down to 50 mm, absorbing setup tolerances without swapping hardware. The retract stroke remains full length.
Built with a stainless-steel barrel and rod for mild washdown resistance, this Ø25 bore unit conforms to the ISO 6432 mounting interface and accepts standard mini brackets. It uses a 1/8" port, a Ø10 mm rod with an M10x1.25 male thread, and fixed TPU bumper pads for end deceleration.
Airtac MIJ Adjustable Cylinder MIJ25X80-30 Technical Specifications
| Model | Airtac MIJ Adjustable Cylinder MIJ25X80-30 |
|---|---|
| Series | MIJ ISO 6432 mini cylinder |
| Bore size | Ø25 mm |
| Stroke | 80 mm |
| Acting type | Double acting, double rod, adjustable stroke |
| Port size | 1/8" |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Fixed TPU bumper pads |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G.
Theoretical Output Force (Ø25mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 206 N |
| 0.7 MPa | 289 N |
| Max (@1.0 MPa) | 42 kgf |
MIJ / MICJ are double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
Model Code: Airtac MIJ Adjustable Cylinder MIJ25X80-30
| MIJ | ISO 6432 round-body mini cylinder (adjustable-stroke). |
|---|---|
| 25 | Bore size in mm. |
| ×80 | Stroke length in mm. |
| -30 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (double rod, adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MIJ Adjustable Cylinder MIJ25X80-30 Is Used
Staged Diverter Stops
Set precise extend positions between 50 mm and 80 mm to deflect packages of varying sizes on a belt without fabricating multiple hard stops.
Adjustable Feed Pusher
Push cartons into a sealing station and fine-tune the forward end position on site to accommodate minor box length variations.
Is the Airtac MIJ Adjustable Cylinder MIJ25X80-30 the Right Cylinder?
The 30 mm adjuster is ideal for changeover jobs where one part number must cover several intermediate stops. Mount via LB foot, FA flange, or TC trunnion (SDB pivot-block is not available on this adjustable variant).
Because this SKU lacks the -S magnet, it cannot accept CMSG, DMSG, or EMSG sensors. Note that the stop screw sets the end position but acts as no mid-stroke lock; the piston will drift on air loss. Use an external rod lock or pilot check valve for held loads.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MIJ Adjustable Cylinder MIJ25X80-30 FAQ
The theoretical maximum force is 50 kgf at 1.0 MPa. The air port is 1/8" and the male rod thread is M10x1.25.
An external stop screw shortens the extend stroke by up to 30 mm, but the retract stroke remains full length. This SKU has no magnet (-S omitted), so it cannot accept CMSG, DMSG, or EMSG sensors. The stainless build resists mild corrosion.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac MIJ Adjustable Cylinder MIJ25X80-30
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.