Airtac MIJ Adjustable Cylinder MIJ40X15-10S
The AirTAC MIJ Adjustable Cylinder MIJ40X15-10S is a genuine double acting, double rod, adjustable stroke round-body mini air cylinder with a Ø40mm bore and 15mm stroke, 1/4" air ports and a stainless-steel barrel and rod for mildly corrosive environments.
- BoreØ40 mm
- Stroke15 mm
- Port size1/4"
- Acting typeDouble acting, double rod, adjustable stroke
- Rod threadM12×1.25
- CushionFixed TPU bumper pads
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MIJ Adjustable Cylinder MIJ40X15-10S
Dial in a precise forward end position on-site with this stainless-steel round-body mini cylinder. The external stop screw on the MIJ40X15-10S shortens the extend stroke by up to 10 mm, allowing you to tune the forward travel from 5 to 15 mm without swapping components; retract remains at the full stroke length. The 1/4" port and M12x1.25 male rod thread handle robust pneumatic flow for heavy duty cycles.
The stainless barrel and piston rod resist mild corrosion and washdown environments, while the built-in magnet (-S) supports CMSG, DMSG, and EMSG sensors for position detection.
Airtac MIJ Adjustable Cylinder MIJ40X15-10S Technical Specifications
| Model | Airtac MIJ Adjustable Cylinder MIJ40X15-10S |
|---|---|
| Series | MIJ mini cylinder |
| Bore size | Ø40 mm |
| Stroke | 15 mm |
| Acting type | Double acting, double rod, adjustable stroke |
| Port size | 1/4" |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Fixed TPU bumper pads |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G. Note: the Ø40 bore is a larger, non-ISO-6432 size.
Theoretical Output Force (Ø40mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 528 N |
| 0.7 MPa | 739 N |
| Max (@1.0 MPa) | 108 kgf |
MIJ / MICJ are double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
Model Code: Airtac MIJ Adjustable Cylinder MIJ40X15-10S
| MIJ | round-body mini cylinder (adjustable-stroke). |
|---|---|
| 40 | Bore size in mm. |
| ×15 | Stroke length in mm. |
| -10 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (double rod, adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MIJ Adjustable Cylinder MIJ40X15-10S Is Used
Staged Diverting
Sort heavy packages on a line by extending the rod 5 to 15 mm to push items into branching lanes, fine-tuning the travel distance on-site without changing hardware.
Is the Airtac MIJ Adjustable Cylinder MIJ40X15-10S the Right Cylinder?
For lighter push requirements, stepping down to the MIJ32 bore yields 402.2 N at 0.5 MPa, whereas this 40 mm bore provides a robust 628.3 N. If your application demands even more force, there is no larger standard MIJ option available. The 10 mm adjustment window is ideal for taking up mechanical tolerances during setup or accommodating multiple stopping points in a changeover job using a single part number.
Position holding is not inherent to this cylinder; the piston will drift if air pressure is lost, as the fixed TPU bumper pads only decelerate the stroke end rather than locking the rod. For suspended or vertical loads, integrate an external rod lock or a pilot-operated check valve. Mounting options include LB foot, FA flange, and TC trunnion brackets (the SDB pivot block is excluded on this adjustable variant), operating at speeds of 30-800 mm/s.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MIJ Adjustable Cylinder MIJ40X15-10S FAQ
The theoretical maximum force is 128.1 kgf at 1.0 MPa.
An external stop screw shortens the extend stroke by up to 10 mm (yielding a 5-15 mm usable forward range), while retract remains full. The -S suffix indicates a built-in piston magnet for use with CMSG, DMSG, or EMSG sensors; the stainless steel build offers mild corrosion resistance.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac MIJ Adjustable Cylinder MIJ40X15-10S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.