Airtac MIJ Adjustable Cylinder MIJ40X160-10S
The AirTAC MIJ Adjustable Cylinder MIJ40X160-10S is a genuine double acting, double rod, adjustable stroke round-body mini air cylinder with a Ø40mm bore and 160mm stroke, 1/4" air ports and a stainless-steel barrel and rod for mildly corrosive environments.
- BoreØ40 mm
- Stroke160 mm
- Port size1/4"
- Acting typeDouble acting, double rod, adjustable stroke
- Rod threadM12×1.25
- CushionFixed TPU bumper pads
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MIJ Adjustable Cylinder MIJ40X160-10S
Dial in your forward travel precisely on-site with the AirTAC MIJ40X160-10S, a round-body stainless steel mini cylinder featuring a 10 mm external stop screw that shortens the extend stroke from its 160 mm nominal length. Retract remains full, while the forward end position is easily fine-tuned to absorb mechanical tolerances or handle changeovers without swapping hardware.
Built with a riveted stainless-steel barrel and a Ø16 mm piston rod, this unit resists mild corrosion and washdown environments. It uses a 1/4" port and an M12x1.25 male rod thread. Because it is a Ø40 bore, it is a non-ISO-6432 round-body design. The integrated magnet (-S) supports CMSG, DMSG, and EMSG sensors for position feedback.
Airtac MIJ Adjustable Cylinder MIJ40X160-10S Technical Specifications
| Model | Airtac MIJ Adjustable Cylinder MIJ40X160-10S |
|---|---|
| Series | MIJ mini cylinder |
| Bore size | Ø40 mm |
| Stroke | 160 mm |
| Acting type | Double acting, double rod, adjustable stroke |
| Port size | 1/4" |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Fixed TPU bumper pads |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G. Note: the Ø40 bore is a larger, non-ISO-6432 size.
Theoretical Output Force (Ø40mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 528 N |
| 0.7 MPa | 739 N |
| Max (@1.0 MPa) | 108 kgf |
MIJ / MICJ are double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
Model Code: Airtac MIJ Adjustable Cylinder MIJ40X160-10S
| MIJ | round-body mini cylinder (adjustable-stroke). |
|---|---|
| 40 | Bore size in mm. |
| ×160 | Stroke length in mm. |
| -10 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (double rod, adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MIJ Adjustable Cylinder MIJ40X160-10S Is Used
Heavy Diverter Gate
Shifts a weighted routing gate on a packaging line, using the 10 mm extend stop to fine-tune the gate angle for different carton widths without repositioning the cylinder.
Film Roll Tensioner
Extends to apply holding pressure on a wrapping film roll, using the stainless build for washdown durability and the stop screw to dial in exact tensioning distance.
Is the Airtac MIJ Adjustable Cylinder MIJ40X160-10S the Right Cylinder?
There is no larger standard MIJ bore, so for loads exceeding this class, consider a different series entirely. The 10 mm external stop screw is ideal for taking up slack during setup or matching multiple stopping points with a single part number.
Keep in mind the stop screw sets the end position but is not a mid-stroke lock; the piston will drift if air pressure is lost, so add an external rod lock or pilot check valve for holding loads. Mounting options include LB foot, FA flange, and TC trunnion (SDB pivot-block is not available on this adjustable variant). Fixed TPU bumper pads decelerate the stroke ends across the 30-800 mm/s speed range.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MIJ Adjustable Cylinder MIJ40X160-10S FAQ
The theoretical maximum force is 128.1 kgf at 1.0 MPa.
An external stop screw shortens the extend stroke by up to 10 mm on-site, allowing forward end-position tuning without changing the cylinder; retract travel remains full. The -S suffix indicates a built-in piston magnet for use with CMSG, DMSG, or EMSG sensors.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac MIJ Adjustable Cylinder MIJ40X160-10S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.