Airtac MIJ Adjustable Cylinder MIJ40X160-30
The AirTAC MIJ Adjustable Cylinder MIJ40X160-30 is a genuine double acting, double rod, adjustable stroke round-body mini air cylinder with a Ø40mm bore and 160mm stroke, 1/4" air ports and a stainless-steel barrel and rod for mildly corrosive environments.
- BoreØ40 mm
- Stroke160 mm
- Port size1/4"
- Acting typeDouble acting, double rod, adjustable stroke
- Rod threadM12×1.25
- CushionFixed TPU bumper pads
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MIJ Adjustable Cylinder MIJ40X160-30
Dial in your forward end position on-site with the AirTAC MIJ40X160-30, a round-body stainless steel mini cylinder featuring a 30mm extend-stroke adjustment window. The external stop screw lets you trim the forward travel from 160mm down to 130mm, absorbing setup tolerances without swapping hardware. Because this is a double-acting actuator, retract travel remains full length.
Built with a stainless barrel and piston rod, this riveted construction resists mild corrosion and washdown environments. The Ø40mm bore delivers substantial force, pushing 628.3N and pulling 527.8N at 0.5MPa. It uses a 1/4" port and fixed TPU bumper pads to decelerate the stroke end.
Airtac MIJ Adjustable Cylinder MIJ40X160-30 Technical Specifications
| Model | Airtac MIJ Adjustable Cylinder MIJ40X160-30 |
|---|---|
| Series | MIJ mini cylinder |
| Bore size | Ø40 mm |
| Stroke | 160 mm |
| Acting type | Double acting, double rod, adjustable stroke |
| Port size | 1/4" |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Fixed TPU bumper pads |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G. Note: the Ø40 bore is a larger, non-ISO-6432 size.
Theoretical Output Force (Ø40mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 528 N |
| 0.7 MPa | 739 N |
| Max (@1.0 MPa) | 108 kgf |
MIJ / MICJ are double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
Model Code: Airtac MIJ Adjustable Cylinder MIJ40X160-30
| MIJ | round-body mini cylinder (adjustable-stroke). |
|---|---|
| 40 | Bore size in mm. |
| ×160 | Stroke length in mm. |
| -30 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (double rod, adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MIJ Adjustable Cylinder MIJ40X160-30 Is Used
Staged Diverting
Trim the 160mm extend stroke by up to 30mm to push heavy cartons onto specific takeaway lanes without repositioning the cylinder body.
Variable Depth Sealing
Leverage the 32kg vertical lift capacity to press varied box sizes, adjusting the forward stop on the controller to prevent crushing.
Is the Airtac MIJ Adjustable Cylinder MIJ40X160-30 the Right Cylinder?
The 30mm external stop screw is ideal for changeover jobs, letting one part number cover several intermediate stops.
Remember that the stop screw only sets the end position, it is not a mid-stroke lock. The piston will drift on air loss, so add an external rod lock or pilot check valve for holding vertical loads. Mount via LB foot, FA flange, or TC trunnion, noting the SDB pivot block is not offered on this adjustable variant. Because this SKU lacks the -S magnet, it cannot accept CMSG, DMSG, or EMSG sensors.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MIJ Adjustable Cylinder MIJ40X160-30 FAQ
At 0.5MPa it pushes 628.3N and pulls 527.8N. At 0.7MPa it pushes 879.6N and pulls 738.9N. The theoretical maximum force is 128.1kgf at 1.0MPa.
An external screw shortens the extend stroke by up to 30mm, but retract remains full. This SKU has no magnet, so it cannot take sensors; you need the -S version for CMSG/DMSG/EMSG switches.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac MIJ Adjustable Cylinder MIJ40X160-30
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.