Airtac MIJ Adjustable Cylinder MIJ40X225-75S
The AirTAC MIJ Adjustable Cylinder MIJ40X225-75S is a genuine double acting, double rod, adjustable stroke round-body mini air cylinder with a Ø40mm bore and 225mm stroke, 1/4" air ports and a stainless-steel barrel and rod for mildly corrosive environments.
- BoreØ40 mm
- Stroke225 mm
- Port size1/4"
- Acting typeDouble acting, double rod, adjustable stroke
- Rod threadM12×1.25
- CushionFixed TPU bumper pads
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MIJ Adjustable Cylinder MIJ40X225-75S
Dial in a precise forward end position on the fly with the AirTAC MIJ40X225-75S, a round-body stainless mini cylinder built for double-acting operation. An external stop screw lets you shorten the extend stroke by up to 75 mm on-site, giving a usable forward range of 150 to 225 mm while maintaining a full retract. This on-site adjustability allows one part number to cover several stroke stops, absorbing mechanical tolerances during setup without swapping cylinders.
The stainless-steel barrel and Ø16 mm piston rod resist mild corrosion and washdown environments, and the -S suffix means a built-in magnet is present for CMSG, DMSG, or EMSG position sensing. It runs on filtered air at 30-800 mm/s with fixed TPU bumper pads to decelerate the stroke end. As a larger bore, it is a non-ISO-6432 round-body design.
Airtac MIJ Adjustable Cylinder MIJ40X225-75S Technical Specifications
| Model | Airtac MIJ Adjustable Cylinder MIJ40X225-75S |
|---|---|
| Series | MIJ mini cylinder |
| Bore size | Ø40 mm |
| Stroke | 225 mm |
| Acting type | Double acting, double rod, adjustable stroke |
| Port size | 1/4" |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Fixed TPU bumper pads |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G. Note: the Ø40 bore is a larger, non-ISO-6432 size.
Theoretical Output Force (Ø40mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 528 N |
| 0.7 MPa | 739 N |
| Max (@1.0 MPa) | 108 kgf |
MIJ / MICJ are double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
Model Code: Airtac MIJ Adjustable Cylinder MIJ40X225-75S
| MIJ | round-body mini cylinder (adjustable-stroke). |
|---|---|
| 40 | Bore size in mm. |
| ×225 | Stroke length in mm. |
| -75 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (double rod, adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MIJ Adjustable Cylinder MIJ40X225-75S Is Used
Staged Diverting
Set the extend stop between 150 and 225 mm to push varied carton sizes onto branching conveyor lanes without changing the actuator.
Variable Sealing
Fine-tune the forward stroke up to 75 mm to press different film thicknesses, relying on fixed TPU bumpers to soften the final impact.
Is the Airtac MIJ Adjustable Cylinder MIJ40X225-75S the Right Cylinder?
The external adjuster is ideal for taking up mechanical tolerances during changeover, but remember it only trims the extend end and is not a mid-stroke lock. Because a plain cylinder drifts on air loss, you must add an external rod lock or pilot check valve to hold a suspended load. Mount via LB foot, FA flange, or TC trunnion (SDB pivot-block is unavailable here), and leverage the -S magnet for electronic or reed sensors.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MIJ Adjustable Cylinder MIJ40X225-75S FAQ
The theoretical maximum force is 128.1 kgf at 1.0 MPa.
An external stop screw shortens the extend stroke by up to 75 mm on-site, but retract remains full and the screw is not a mid-stroke lock. The -S suffix indicates a built-in piston magnet for CMSG, DMSG, or EMSG sensors, and the stainless build resists mild corrosion.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac MIJ Adjustable Cylinder MIJ40X225-75S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.