Airtac MIJ Adjustable Cylinder MIJ40X60-10
The AirTAC MIJ Adjustable Cylinder MIJ40X60-10 is a genuine double acting, double rod, adjustable stroke round-body mini air cylinder with a Ø40mm bore and 60mm stroke, 1/4" air ports and a stainless-steel barrel and rod for mildly corrosive environments.
- BoreØ40 mm
- Stroke60 mm
- Port size1/4"
- Acting typeDouble acting, double rod, adjustable stroke
- Rod threadM12×1.25
- CushionFixed TPU bumper pads
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MIJ Adjustable Cylinder MIJ40X60-10
Dial in your forward end position on-site with the AirTAC MIJ40X60-10, a round-body stainless steel mini cylinder featuring a 10mm extend-stroke adjustment window. An external stop screw lets you trim the forward stroke down from the 60mm nominal maximum, absorbing setup tolerances without changing the part number. Retract remains full stroke.
It uses fixed TPU bumper pads to decelerate the stroke end and features a 1/4" port with a 16mm rod.
Airtac MIJ Adjustable Cylinder MIJ40X60-10 Technical Specifications
| Model | Airtac MIJ Adjustable Cylinder MIJ40X60-10 |
|---|---|
| Series | MIJ mini cylinder |
| Bore size | Ø40 mm |
| Stroke | 60 mm |
| Acting type | Double acting, double rod, adjustable stroke |
| Port size | 1/4" |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Fixed TPU bumper pads |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G. Note: the Ø40 bore is a larger, non-ISO-6432 size.
Theoretical Output Force (Ø40mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 528 N |
| 0.7 MPa | 739 N |
| Max (@1.0 MPa) | 108 kgf |
MIJ / MICJ are double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
Model Code: Airtac MIJ Adjustable Cylinder MIJ40X60-10
| MIJ | round-body mini cylinder (adjustable-stroke). |
|---|---|
| 40 | Bore size in mm. |
| ×60 | Stroke length in mm. |
| -10 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (double rod, adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MIJ Adjustable Cylinder MIJ40X60-10 Is Used
Precision Press Fit
Trimming the extend stroke by up to 10mm allows exact forward positioning for pressing bearings, compensating for material thickness variations without swapping actuators.
Vertical Lift Stop
Lifting approximately 32 kg of raw material in a staged feed, using the adjustable forward end position to set precise drop heights across multiple machine setups.
Is the Airtac MIJ Adjustable Cylinder MIJ40X60-10 the Right Cylinder?
When sizing this 40mm bore, check both directions: stepping down to the MIJ32 drops the 0.5 MPa push force to 402.2 N, while this MIJ40 provides 628.3 N. If your application needs less than 402.2 N, the smaller bore saves space, but this 40mm unit is the top choice for heavier pushes up to a 128.1 kgf theoretical maximum at 1.0 MPa. The 10mm external stop screw is ideal for taking up mechanical tolerances during changeovers.
Because this SKU lacks the -S magnet, it cannot accept CMSG, DMSG, or EMSG sensors. Mount using LB foot, FA flange, or TC trunnion brackets, or CA, U, R, and CM back covers. Note that the SDB pivot block is not available on this adjustable variant. The stop screw sets the end position but is not a mid-stroke lock; the piston will drift on air loss, so add an external rod lock or pilot check valve for held loads.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MIJ Adjustable Cylinder MIJ40X60-10 FAQ
The theoretical maximum force is 128.1 kgf at 1.0 MPa. The air port is 1/4" and the male rod thread is M12x1.25.
An external stop screw shortens the extend stroke by up to 10mm on-site, giving a usable forward range of 50-60mm; retract remains full. This SKU has no magnet, so it cannot take position sensors. The -S variant adds a magnet for CMSG, DMSG, or EMSG switches.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac MIJ Adjustable Cylinder MIJ40X60-10
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.