verified AirTAC China Authorized Export Seller shield 100% Genuine AirTAC Parts workspace_premium 1-Year Warranty
appsShop by Modelexpand_more
person shopping_cart Request a QuoteQuote
AirTAC 100M · Manifold gasket / seal kit

Airtac P Air Valve Gaskets P-100M-R1

The AirTAC P Air Valve Gaskets P-100M-R1 is a genuine gasket and screw kit for the 100M manifold. It replaces the station seals that sit between each valve and the base - the usual cure when a manifold starts leaking between stations.

  • Part typeManifold gasket / seal kit
  • Manifold100M
  • Kit contentsManifold seal and screw
  • Order codeR1
$6.97 Standard part — ready in 3-5 business days to process and dispatch
Request a Quote
  • No minimum order. A single piece can be ordered.
  • Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
verified Genuine AirTAC workspace_premium 1-year warranty bolt Reply in 7-8 h

About the Airtac P Air Valve Gaskets P-100M-R1

The P-100M-R1 is the gasket and seal kit for AirTAC's 100M manifold base, the bar that carries 4A100 air-pilot and 4V100 or 5V100 solenoid valves in a single row. The kit holds the station seal and its screw - that is the complete content - and its only job is to close the joint between a valve body and the base so the common inlet cannot leak past a station. It does not repair or alter the valve itself.

Because each kit serves exactly one valve position, size the job before you order: a 4-station 100M bank takes 4 kits for a full re-seal, and a 16-station bank, the maximum the 100M base accepts, takes 16. Replacing a tired station seal stops the hiss of air escaping around a valve that is otherwise perfectly serviceable, which is far cheaper than replacing working valves.

Airtac P Air Valve Gaskets P-100M-R1 Technical Specifications

ModelAirtac P Air Valve Gaskets P-100M-R1
Part typeManifold gasket / seal kit
Manifold series100M
Fits valve bodies4A100 air pilot and 4V100 / 5V100 solenoid
Kit contentsManifold seal and screw
FluidAir (filtered by 40µm element)
Temperature-20 to +70 °C
ReplacesThe gasket kit on any 100M station
Sold asOne kit per station

This is a service part for the 100M manifold, not a valve. Check the manifold body size stamped on your base before ordering: a 100M gasket kit does not fit a different body size.

Model Code: Airtac P Air Valve Gaskets P-100M-R1

PKit / service part.
100MFor the 100M manifold.
R1R1 = gasket / seal kit (seal + screw).

How a Manifold Bank Goes Together

  • check One PT1/4 inlet feeds every station, so you run a single supply drop.
  • check Each station takes one 100-body valve; the A and B work ports stay on the valve.
  • check Exhausts collect in the base — silence the bank once instead of per valve.
  • check Any station you are not using yet takes a P-100M-R2 blank plate.
  • check Station seals are a serviceable part: P-100M-R1.

Where the Airtac P Air Valve Gaskets P-100M-R1 Is Used

handyman

Service van stock for valve banks

A maintenance engineer carrying P-100M-R1 kits can re-seal any 100M manifold on site without pulling the whole bank apart - one kit per leaking station is all the job needs.

factory

Packaging machine re-seal during shutdown

Wrapping lines often run four or more 4V100 valves on one 100M base; a full re-seal at annual shutdown means ordering 4 kits for a 4-station bar, and 16 for a fully loaded one.

science

Laboratory air manifold silence

A lab air distribution bench built on a 100M manifold loses low-pressure signal to a leaking station seal; fitting this kit cures the leak between valve and base without touching the valves.

Is the Airtac P Air Valve Gaskets P-100M-R1 the Right Part?

Confirm the base before ordering: AirTAC stamps the manifold type on the bar, so look for the 100M marking and for the 1/4" common inlet and M5 or 1/8" station ports that identify a 100-body base. This kit suits only that base - a 200M, 300M or 400M bar needs its own gasket kit, and the blank plates for closing unused 100M stations are a separate part, the P-100M-R2.

Count your fitted valves, not your potential stations: the kit count you need is the number of valve positions currently sealed into the base, not the number of positions the base could take. If one station is leaking while the rest of the bank is sound, a single kit is enough.

Quick checklist

  • ✓ Valve body size (100) matches the base
  • ✓ One kit covers one station
  • ✓ Body size stamped on your manifold
Ask an Engineer

Airtac P Air Valve Gaskets P-100M-R1 FAQ

One kit covers exactly one valve station, and each kit contains one station seal and one screw - nothing else. So a fully loaded 100M base at its 16-station maximum needs 16 kits for a complete re-seal, a 4-valve bank needs 4, and a single weeping station needs 1. The base's 1/4" common inlet and M5 or 1/8" station ports stay untouched by the job.

Check that the bar is marked 100M and that the valves sitting on it are 100-body AirTAC units - the air-pilot 4A100 or the solenoid 4V100 and 5V100. If so, this kit fits. It seals the joint between valve and base only: it cures leakage at that joint and changes nothing about how the valve shifts or how the circuit works.

verified

Authorized Export Seller

Genuine AirTAC parts produced by AirTAC factory.

workspace_premium

1-Year Warranty

Covers non-human-caused product damage.

local_shipping

Fast Dispatch

Standard parts are processed and dispatched in 3-5 business days.

bolt

Fast Reply

Most inquiries answered within 7-8 hours.

Request a Quote for Airtac P Air Valve Gaskets P-100M-R1

Send us the quantity, thread standard and destination. We confirm price, stock and lead time — usually within 7-8 hours.

Thank you. We received your request for P-100M-R1 and will confirm price, stock and lead time — usually within 7-8 hours.

For the fastest response, keep the complete model number above and include a clear photo of the product label. If photo upload is unavailable, email photos to [email protected] with your model number.