Airtac RMH Magnetic Coupling Rodless Cylinder RMH10X150S
Genuine AirTAC magnetic rodless cylinder, order code RMH10X150S from the RMH range. The options this code selects are decoded below; series data follow the official AirTAC catalog.
- BoreØ10 mm
- Stroke150 mm
- Port threadM5×0.8
- ActionDouble acting, magnetic coupling
- GuideBuilt-in guide rail
- Ø10holding force 55 N · strokes to 300 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac RMH Magnetic Coupling Rodless Cylinder RMH10X150S
A 150 mm slide travel sits in the middle of the Dia 10 stroke range, which runs to 300 mm, so this unit buys 50 mm more reach than the RMH10X100S without leaving the compact envelope of a rodless design. Magnets drive the slide directly, meaning there is no piston rod to bend, side-load or seal.
Holding force is 55 N and the built-in guide rail takes over the anti-rotation and load-carrying duties that a rod cylinder normally assigns to its rod. Air enters through M5x0.8 ports on one side of the body, speed can be set anywhere from 50 to 400 mm/s, and fixed cushions with adjusting screws soften both ends; hydraulic shock absorbers can be ordered separately to replace them.
Airtac RMH Magnetic Coupling Rodless Cylinder RMH10X150S Technical Specifications
| Order code | RMH10X150S |
|---|---|
| Product | Magnetic Rodless Cylinder |
| Bore | Ø10 mm |
| Stroke | 150 mm |
| Port thread | M5×0.8 |
| Action | Double acting, magnetic coupling |
|---|---|
| Guide | Built-in guide rail |
| Ø10 | holding force 55 N · strokes to 300 mm |
| Ø16 | holding force 140 N · strokes to 500 mm |
| Ø20 | holding force 220 N · strokes to 800 mm |
| Ø25 | holding force 345 N · strokes to 800 mm |
| Fluid | Air (filtered by 40 µm element) |
| Operating pressure | 0.2-0.7 MPa |
| Proof pressure | 1.2 MPa (175 psi) |
| Temperature | -20 to +70 °C |
| Speed | 50-400 mm/s |
| Stroke tolerance | +1.0 / 0 mm (≤250), +1.5 / 0 mm (251-800) |
| Cushion | Fixed, adjusting screws |
| Sensors | CMSH, DMSH, EMSH |
| Port | M5×0.8 (Ø10, 16), PT1/8 (Ø20, 25) |
Source: AirTAC Products Catalog 2026A (PDF01-P0612..P0613), RMH series specifications, load tables, strokes and ordering code.
How to choose
Choose RMH10X150S when the application needs the extra 50 mm over RMH10X100S but the 200 mm of RMH10X200S travel would be wasted. All three share the Dia 10 bore, M5x0.8 ports and 55 N magnetic coupling, so stroke is the deciding difference. For loads beyond the Dia 10 table or forces approaching 55 N, move to the Dia 16 series with 140 N of holding force.
Applications
Mid-stroke lift station
Raise or lower small parts through 150 mm; the guide rail holds the slide square so the load does not twist the coupling.
Sliding guard and cover drive
Move machine-guard doors or covers over 150 mm, with cushion adjusting screws letting you tune deceleration at each end.
Small-component feed slide
Feed parts from a hopper to a nest at 50 to 400 mm/s, with CMSH, DMSH or EMSH switches reporting mid-stroke positions from the groove.
FAQ
What are the key figures of the RMH10X150S?
Dia 10 mm bore, 150 mm stroke, double-acting magnetic coupling with built-in guide rail, M5x0.8 ports, 55 N holding force, 0.2-0.7 MPa operating pressure, 50-400 mm/s speed, -20 to +70 C, air filtered to 40 um. Stroke tolerance is +1.0 / 0 mm because the stroke is under 250 mm.
How much load can the slide carry at 150 mm?
The catalog rates the Dia 10 bore at 1.4 / 2.4 kg up to 200 mm stroke, and the allowed load falls on longer strokes, so verify the load table for your mounting orientation at 150 mm. The built-in guide rail raises running accuracy, anti-rotation accuracy and load capacity over the bare coupling.