Airtac SAIJ160 Adjustable Cylinder SAIJ160BX110-40S
The AirTAC SAIJ160 Adjustable Cylinder SAIJ160BX110-40S is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø160mm bore and 110mm stroke, G3/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
- BoreØ160 mm
- Stroke110 mm
- Port sizeG3/4
- Acting typeDouble acting
- Rod threadM36×2
- CushionAdjustable, 50 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac SAIJ160 Adjustable Cylinder SAIJ160BX110-40S
The AirTAC SAIJ160X110-40-S is a double-acting ISO 15552 profile cylinder equipped with a rear stroke adjuster, providing a usable travel window of 70 to 110 mm. The extruded aluminum barrel integrates dual-side sensor grooves, and this specific configuration includes a SUS304 stainless steel rod and a PT tapered port thread.
Because the rear adjuster acts purely as a mechanical stop for end-position tuning, it does not hold the load without live air pressure. For load-holding requirements without continuous air, consider the related SAIL pneumatic lock or BSAI clamp-lock series. This cylinder supports a speed range of 30-500 mm/s and uses the reduced SAIJ mounting set: Basic, FA, LB, TC, FTC, TCM1, and TCM2.
Airtac SAIJ160 Adjustable Cylinder SAIJ160BX110-40S Technical Specifications
| Model | Airtac SAIJ160 Adjustable Cylinder SAIJ160BX110-40S |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø160 mm |
| Stroke | 110 mm |
| Acting type | Double acting |
| Port size | G3/4 |
| Rod thread | M36×2 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Adjustable, 50 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
Theoretical Output Force (Ø160mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 9425 N | 9425 N |
| 0.7 MPa | 13195 N | — |
| Max (@1.0 MPa) | 1922 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SAIJ160 Adjustable Cylinder SAIJ160BX110-40S
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 160 | Bore size in mm. |
| ×110 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Where the Airtac SAIJ160 Adjustable Cylinder SAIJ160BX110-40S Is Used
Press Stroke Calibration
Dial in the exact 70-110 mm travel window during press commissioning to accommodate varying material thicknesses without installing secondary external stoppers.
Product Changeover Systems
Rapidly adjust the retract end-position on automated assembly lines when switching between different product sizes, leveraging the 40 mm adjustment range.
Is the Airtac SAIJ160 Adjustable Cylinder SAIJ160BX110-40S the Right Cylinder?
Select this 160 mm bore adjustable-stroke model when a machine setup requires fine-tuning the retract end-position during commissioning or product changeover without swapping out the entire cylinder or adding external stops. Conversely, moving up to the 200 mm bore provides 21991 N at 0.7 MPa. When matching ISO 15552 interchangeability replacements, confirm the 110 mm stroke, 40 mm adjustment range, PT port, and the -S magnet for CMSE and DMSE sensors.
Although the 110 mm stroke is relatively short, the 40 mm diameter rod and M36x2 thread handle substantial side loads effectively. Remember that the rear adjuster only sets the travel end and relies on the built-in air cushion for deceleration; it is not a locking mechanism. For any load-holding safety requirements, an external rod lock or pilot-operated check valve is necessary.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/NPT/G)
- ✓ Magnet (-S) for sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (FA/FB/CA/CB/LB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac SAIJ160 Adjustable Cylinder SAIJ160BX110-40S FAQ
It features a rear adjusting screw that shortens the effective stroke by up to 40 mm, creating a usable travel window between 70 and 110 mm. This allows you to fine-tune the end position at commissioning without changing the cylinder itself.
The -S suffix means it includes a magnet compatible with AirTAC CMSE reed switches and DMSE electronic sensors mounted in the dual-side barrel grooves.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC SAI Cylinders
Request a Quote for Airtac SAIJ160 Adjustable Cylinder SAIJ160BX110-40S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.