
The AirTAC SAIJ50 Adjustable Cylinder SAIJ50X155-20 is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø50mm bore and 155mm stroke, G1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAIJ50X155-20 is a double-acting ISO 15552 profile cylinder featuring a rear stroke adjuster that allows you to fine-tune the effective travel down to a 135-155 mm window without adding external stops. It features a 20 mm adjustment range and a carbon steel piston rod with PT tapered ports.
The extruded aluminum barrel includes sensor grooves on both sides for direct mounting of CMSE reed or DMSE electronic switches. This adjustable variant utilizes a reduced mounting subset (Basic, FA, LB, TC, FTC, TCM1, TCM2), omitting the FB, CA, CB, and CR brackets. The rear adjuster functions strictly as a mechanical stop to set the end position, not as a locking device.
| Model | Airtac SAIJ50 Adjustable Cylinder SAIJ50X155-20 |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø50 mm |
| Stroke | 155 mm |
| Acting type | Double acting |
| Port size | G1/4 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 825 N | 825 N |
| 0.7 MPa | 1155 N | — |
| Max (@1.0 MPa) | 168 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 50 | Bore size in mm. |
| ×155 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Dial in the 135-155 mm retract distance on the fly when switching product sizes on a packaging line, avoiding the need to physically swap out the entire cylinder.
Precisely set the exact bottom-out position for a pressing or spotting operation, using the 20 mm adjustment range to compensate for mechanical wear or tooling tolerances.
Provide adjustable physical stops for an indexing mechanism where the exact end position must be verified and tweaked during initial equipment setup.
If your setup needs less force, stepping down to a 40 mm bore yields 628 N; if you need more power, a 63 mm bore provides 1559 N. The 16 mm rod and M12x1.25 thread offer robust resistance to side loading, though any stroke over 300 mm would require external guide rails to prevent premature seal wear.
Choose the SAIJ adjustable-stroke design over a fixed SAI cylinder when you need to dial in the exact retract distance during commissioning or product changeovers. Because the rear adjuster only halts forward travel and relies on live air to maintain pressure, it cannot hold a load pneumatically without continuous air supply. For dead-stop load holding without live pressure, consider the SAIL or BSAI series instead.
Quick checklist
At the maximum operating pressure of 1.0 MPa, it delivers up to 200 kgf.
The rear adjuster acts as a mechanical stopper that lets you shorten the nominal 155 mm stroke by up to 20 mm, creating a usable travel window of 135-155 mm. It allows for fine-tuning the end position at commissioning without replacing the cylinder.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.