
The AirTAC SAIJ50 Adjustable Cylinder SAIJ50X155-40S is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø50mm bore and 155mm stroke, G1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAIJ50X155-40-S is a double-acting, double-rod ISO 15552 profile cylinder featuring a rear-mounted stroke adjuster. The integrated -S magnet enables direct mounting of CMSE reed and DMSE electronic sensors along the dual-side extruded barrel grooves for precise end-of-travel detection.
With a 155mm nominal stroke and a 40mm adjustment range, this model provides a usable travel window of 115-155mm. This built-in stopper allows you to fine-tune the retract end position at commissioning without adding external physical stops or swapping the cylinder. The adjuster acts purely as a travel stop to set deceleration limits and does not hold the load without continuous live air pressure.
| Model | Airtac SAIJ50 Adjustable Cylinder SAIJ50X155-40S |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø50 mm |
| Stroke | 155 mm |
| Acting type | Double acting |
| Port size | G1/4 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 825 N | 825 N |
| 0.7 MPa | 1155 N | — |
| Max (@1.0 MPa) | 168 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 50 | Bore size in mm. |
| ×155 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Dial in the exact 115-155mm retract position during product size transitions without disassembling tooling or adding external shims.
Leverage the -S magnet and dual sensor grooves to mount DMSE electronic switches, fine-tuning the actuation signal alongside the physical stroke stop.
Trim the stroke up to 40mm at commissioning to perfect the seating force against a workpiece, preventing over-travel damage.
Select this 50mm bore cylinder when an application requires a variable end-stop within a 115-155mm travel window, stepping down from a 63mm bore (1559N at 0.5MPa) if your force needs are moderate, or stepping up from a 40mm bore (628N) for heavier positioning. It uses a PT tapered G1/4 port and supports the reduced SAIJ mounting set: Basic, FA, LB, TC, FTC, TCM1, and TCM2, omitting the FB, CA, CB, and CR brackets. If your machine requires holding a load securely without live air, this adjustable stop is not a lock; you should instead use an SAIL pneumatic lock, a BSAI clamp-lock, or an external rod lock. Because the 155mm stroke is under 300mm, side-load guide requirements are minimal, but the robust 20mm rod handles standard lateral stress well.
Quick checklist
The rear adjuster screw allows you to shorten the 155mm nominal stroke by up to 40mm, creating a usable travel window of 115-155mm. It functions as a mechanical stop for end-position tuning and does not lock the load without live air.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.