
The AirTAC SAIJ50 Adjustable Cylinder SAIJ50X185-100 is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø50mm bore and 185mm stroke, G1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAIJ50X185-100 is a double-acting ISO 15552 profile cylinder equipped with a rear stroke adjuster. It provides a nominal 185 mm stroke that can be dialed back by up to 100 mm, yielding a highly flexible usable travel window of 85 to 185 mm.
The rear adjustment screw acts purely as a mechanical stop to set the retraction end-point, meaning it cannot hold a load without continuous live air pressure. For position holding without air, a SAIL or BSAI variant would be required. This model features a carbon steel piston rod, PT tapered port threads, and standard variable air cushions at both ends to manage kinetic energy.
| Model | Airtac SAIJ50 Adjustable Cylinder SAIJ50X185-100 |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø50 mm |
| Stroke | 185 mm |
| Acting type | Double acting |
| Port size | G1/4 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 825 N | 825 N |
| 0.7 MPa | 1155 N | — |
| Max (@1.0 MPa) | 168 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 50 | Bore size in mm. |
| ×185 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Dial in the stroke from 85 to 185 mm on the fly to accommodate varying package sizes on a packaging line without changing the cylinder.
Fine-tune the retraction end-position during initial commissioning to achieve precise mechanical alignment without adding external spacers.
Use the 100 mm adjustment range to create multiple programmed end-positions in automated assembly equipment for different product runs.
Selecting this 50 mm bore cylinder makes sense when an application demands a wide range of motion tuning, as the 100 mm adjustment window allows for massive product size changeovers without swapping hardware. If your setup requires less force, stepping down to a 40 mm bore yields 628 N at 0.5 MPa, while moving up to a 63 mm bore provides 1559 N. Because the nominal stroke is 185 mm, an external guide is not strictly mandated for side loads, but the 20 mm rod diameter handles moderate bending stress well.
An adjustable stroke is chosen over a fixed SAI cylinder when commissioning fine-tunes or variable end-stops are necessary, eliminating the need to bolt on external stops. To match this ISO 15552 interchangeable cylinder, confirm the 50 mm bore, 185 mm stroke, 100 mm adjuster, PT G1/4 port, and standard mounting options (Basic, FA, LB, TC, FTC, TCM1, TCM2). Note that the FB, CA, CB, and CR mounts are omitted from the SAIJ series.
Quick checklist
At 0.7 MPa, the push force increases to 1374 N.
The rear adjuster acts as a mechanical stop that lets you trim the effective travel back by up to 100 mm. This creates a usable stroke window of 85 to 185 mm, though it functions only as a stop and does not lock the load without live air.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.