
The AirTAC SAIJ50 Adjustable Cylinder SAIJ50X300-30 is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø50mm bore and 300mm stroke, G1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAIJ50X300-30 is a double-acting, double-rod ISO 15552 profile cylinder equipped with a rear stroke adjuster. By turning the external rear stopper screw, you can trim the effective travel back by up to 30mm, providing a usable stroke window of 270-300mm for precise end-position calibration.
This adjustable feature allows you to fine-tune the retract position at commissioning or during product changeovers without swapping the cylinder or adding external stops. The extruded aluminum barrel includes sensor grooves on both sides, ready for AirTAC CMSE reed and DMSE electronic solid-state switches if a magnet is specified later. It supports a mounting subset of Basic, FA, LB, TC, FTC, TCM1, and TCM2, omitting the FB, CA, CB, and CR footprints.
| Model | Airtac SAIJ50 Adjustable Cylinder SAIJ50X300-30 |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø50 mm |
| Stroke | 300 mm |
| Acting type | Double acting |
| Port size | G1/4 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 825 N | 825 N |
| 0.7 MPa | 1155 N | — |
| Max (@1.0 MPa) | 168 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 50 | Bore size in mm. |
| ×300 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Dial in the retract stop from 270 to 300mm during product size transitions on a packaging line without physically swapping the actuator.
Fine-tune the final retract position during initial commissioning to align tooling perfectly, absorbing mechanical tolerances up to 30mm.
Adjust the stroke end-point on the fly to accommodate different package sizes or push-off distances along a conveyor section.
The 30mm adjustment range is ideal for dialing in variable end-stops on the fly, whereas a fixed-stroke SAI cylinder locks you into a single 300mm travel. Because the stroke is 300mm, the 20mm rod diameter and M16x1.5 rod thread will still experience leverage forces; use an external guide to prevent side-loading damage on the barrel.
For dimensionally interchangeable ISO 15552 replacements, match the 50mm bore, 300mm stroke, 30mm adjustment, PT tapered port threads, and the desired mounting accessory. Remember that the rear adjuster and the variable air cushions at both ends only decelerate the travel—they do not hold the load without live air. For true load-holding without continuous pressure, consider an external rod lock or pilot-operated check valve, or explore the SAIL or BSAI cylinder families.
Quick checklist
At the maximum 1.0 MPa pressure, it can deliver up to 200 kgf.
The rear stopper screw lets you shorten the nominal 300mm stroke by up to 30mm, creating a usable travel window of 270-300mm. This allows you to set the exact retract end-position during setup without adding external stops.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.