
The AirTAC SAIJ50 Adjustable Cylinder SAIJ50X325-40S is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø50mm bore and 325mm stroke, G1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAIJ50X325-40-S is a double-acting ISO 15552 profile cylinder equipped with a rear stroke adjuster, providing a usable travel window of 285 to 325 mm. The extruded aluminum barrel integrates sensor grooves on both sides, ensuring versatile mounting of detection components.
This adjustable-stroke variant allows you to fine-tune the retract end position at commissioning without swapping the cylinder or adding external stops. The rear adjuster acts purely as a travel stop and works alongside the variable air cushions at both ends to decelerate the load. It supports a reduced mounting set including Basic, FA, LB, TC, FTC, TCM1, and TCM2, omitting the FB, CA, CB, and CR options.
| Model | Airtac SAIJ50 Adjustable Cylinder SAIJ50X325-40S |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø50 mm |
| Stroke | 325 mm |
| Acting type | Double acting |
| Port size | G1/4 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 825 N | 825 N |
| 0.7 MPa | 1155 N | — |
| Max (@1.0 MPa) | 168 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 50 | Bore size in mm. |
| ×325 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Dial in the exact 285-325 mm travel distance during product size transitions on a packaging line without swapping out the entire actuator.
Fine-tune the retract stop during machine commissioning to perfect a pressing or clamping operation without fabricating external spacers.
Adjust the stroke on a sorting diverter to accommodate different package lengths on the fly, ensuring accurate routing without hardware changes.
If your process needs less force, stepping down to a 40 mm bore yields 628 N; if more force is required, stepping up to a 63 mm bore provides 1559 N. The 40 mm adjustment range is ideal for product changeovers on a line, allowing you to dial in the exact travel distance without hardware modifications. For position feedback, the integrated -S magnet works seamlessly with AirTAC CMSE reed and DMSE electronic sensors.
Because the nominal stroke is 325 mm, the 20 mm rod diameter and M16x1.5 thread may be subjected to side loads if the tooling is unsupported; an external guide is recommended for heavy or off-center loads to prevent premature seal wear. As an ISO 15552 profile cylinder, it is dimensionally interchangeable with other ISO 15552 cylinders. Configuration: 50 mm bore, 325 mm stroke, 40 mm adjustment, PT G1/4 port, -S magnet, carbon steel rod. Remember that the rear adjuster is a stop, not a lock; for load-holding without live air pressure, consider the SAIL or BSAI series.
Quick checklist
At the maximum 1.0 MPa pressure, it delivers up to 200 kgf of push force.
The rear adjuster allows you to shorten the effective travel from the 325 mm nominal stroke by up to 40 mm, creating a 285-325 mm usable window. The adjuster acts as a mechanical stop to set the end position and does not lock the load without live air pressure.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.